stlink v2 3d models

This developer created a compact debugging tool specifically for STM32 microcontrollers. ...The project can be found at the link below: http://e.pavlin.si/2016/02/22/st-link-v2-on-a-single-sided-diy-pcb/

I created this compact debug tool for debugging the entire STM32 series. ...Check out the full project online: http://e.pavlin.si/2016/02/22/st-link-v2-on-a-single-sided-diy-pcb/.

Case for STLink V2 based on BluePill(stm32f103c8t6)

Hi, this is the case for STLink-V2 programmer which is part of STM32 NUCLEO boards (64 pins or 144 pins). The programmer can be separated from the board and used as standalone device. All available pins are exposed (SWD port, TX, RX, GND, ...). ...

Hi, this is the case for STLink-V2 programmer which is part of STM32 NUCLEO boards (64 pins or 144 pins). ...The programmer can be separated from the board and used as standalone device.</p> <p>All available pins are exposed (SWD port, TX, RX, GND,...

The STLINK-V3MODS is a small size debugging and programming probe for STM32 microcontrollers.

Protective Bottom Cover for STLink-V3SET Device

STLINK-V3 MINI comes in tiny package, but lacks proper enclosure.&nbsp;

STLINK-V3 MINI comes in tiny package, but lacks proper enclosure.

Sleeve for STLINK-V3MINIE. ...Prevents unwanted shorts.It holds only by the power of will. The will of the USB-C connector, that is. Not to be confused with STLINK-V3MINI. ...They are two separate things.

Cover for STlink v3 with mounted adapter PCB to protect the electonics.Part List:- M3 18mm cheese head screw

The new cover empowers users of the STLink/V3 to seamlessly integrate the expansion board. ...Since the original cover is not compatible with this upgrade, a custom-designed and rigorously tested cover has been created specifically for this purpose.

I did not create the adaptor by myself, I used the designed from github: https://github.com/tw1chao/STLinkV3_Adapter https://github.com/TMSL/STLINK-V3MINI-Cable-Adapter-Board Additional parts: - a 5 mm piece of transparent 3 mm Filament as fiber...

I did not create the adaptor by myself, I used the designed from github: https://github.com/tw1chao/STLinkV3_Adapter https://github.com/TMSL/STLINK-V3MINI-Cable-Adapter-Board Additional parts: - a 5 mm piece of transparent 3 mm Filament as fiber...

The cover allows users of the new STLink/V3 to attach the expansion board. ...Original cover isn't suited for this extension, thus a new cover was designed and tested.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>MK3</p> <p><p...

STLink-V3 adapter board cover

The STLink-V3Set debugger comes with a breakout board that offers additional features and a blue plastic shim piece for securing it on the back of the PCB. However, due to design limitations, the original base plate cannot be effectively mounted over...

For those of you who use the Nucleo boards, and snap off the programmer part, here is an enclosure for it. ...

Added mounting tabs to screw-mount the STLink permanently into a one-off project at work

PCBmount for STLINK-V3MINI (V1). Mounted via heated up M3 steel screw or via cable tie. ... Used female plug on the pcb is Wuerth 62301421021 ; RS Stock No.: 233-9742

A custom-designed protective sleeve for the STLink v3 mini module, crafted with a single, seamless piece of friction-fit plastic. The 1.5mm wall thickness is expertly balanced to provide an unobstructed view of the LEDs shining through its...

I ordered two STLink clones for myself and a friend and got started right away. When you remove the pins no longer in use on the back, you're left with an empty space in the casing. This design should fill that gap and allow you to put it on your...

I designed a new spacer because the one provided wasn't working out.

Original: https://www.thingiverse.com/thing:3163349 I have added some guards for sticking out goldpins, and lowered the center extrusion for screw - I got in set a 7mm height brass screw-nut (which is too high for original project). Also I...

V2 Kayak propeller V2

V2

v2

V2

V2

Schleuder V2 / Slingshot V2 Get Ready to Blast Off Print Settings Printer: CTC Rafts: Don't Bother, It's a Breeze Supports: No Way Resolution: 0.1-0.2mm - That's Tiny! ...Infill: 30-50% - Just Right Notes: 5 Shells Waiting to Explode