stl to gcode ender 3 3d models

... to change the temps of the bed if you want. This gcode is designed fro the Ender 3 but it can work whith any printer whith the same size (235 x 235mm). ... (I put a "cube.stl" file juste so I can publish, dont need to download it or print it)

#Ender3 bed leveling gcode ##This gcode moves the print head to positions directly above bed leveling posts # OCTOprint version ##The octoprint version is automated waiting 5 seconds at Z0 above each post # SDCARD-ONLY ##Must be ran from the printer,...

This is a simple tip for those who ask how to automatically retract the filament after printing on printers without an automatic unload function like the Ender 3, so you can remove the spool without having to reheat the nozzle again. The key is to...

This is a simple gcode file to assist in bed leveling on the Creality Ender 3 printer. It has been tested on my Ender 3 Pro, but I believe it should work on other Ender 3 models, as well. You can ignore the wing nut and stub models if you...

The Engineer Created a Customized Temptower Design in Cura and Generated G-code Specifically for the Ender 3 Printer.

This gcode contains 4 points to calibrate (coincident with the screws of the heatbed) plus the center of the bed. ...In order to continue to next point you must press the LCD button. Category: 3D Printing Tests

This G-code includes four calibration points aligned with the heatbed's screw positions, as well as the bed's center. ...To proceed to the next point, press the LCD button.

Ender 3 PLA temp tower. ...To change the temperature automatically download the Gcode

Custom GCode for Ender 3 (Cura) with BLTouch

These are gcode files for an Ender 3 to do feeler leveling and also indicator leveling. The feeler gcode places the nozzle directly over the bed screws for more accurate diagonal bed rocking. The indicator gcode places the indicator directly over...

2020-10-05: This is a remix of CHEP's bed leveling GCode and test print for the Ender 3/Ender 3 Pro running the 8-bit board. Modifications to GCode: - Increased movement speed during X-Y motion - Added parking sequence which moves the nozzle away...

Here is the modified Gcode I use for the cold pull routine on my Ender 3, which I run every time I change filament - specifically for PLA. A big shoutout to 3dviking, whose original code can be found at...

This is a remix of the CHEP ender 3 bed level gcode. I've been using the Chep bed level code for a long time but it is sometimes very slow to travel. I upped the travel speeds and also added a Z lift after the last position. Thanks Chep for all the...

This is a remix of the CHEP ender 3 bed level gcode. I've been using the Chep bed level code for a long time but it is sometimes very slow to travel. I upped the travel speeds and also added a Z lift after the last position. Thanks Chep for all...

There is no bed heating or extrusion with this gcode, which saves a lot of time compared to a couple I tried that other folks had. I also made sure to move the extruder up and out of the way at the end. ... Give it a like/thumbs up if you find it...

Here is a video of the file running on my Ender 3 V2: https://youtu.be/0biRmz_sqUo Note: This code is specifically designed to heat your extruder up to 210 degrees Celsius and will not work for any other filament except for PLA. The g-code is easily...

Ender 3 Tests: 1. Movement 2. Accuracy 3. Heating 4. Leveling 5. Printing 6. Error translation (Resets the printer) DO NOT make the G-Code any faster than it is. BL-Touch is not supported by this. ... Compatible with any Marlin printer that has...

Try this!Using 60c bed temp and 200c hotend temp.To increase printing speed of non planar layers use M203 Z15 to increase the max Z axis speedAlthough even with the stock fans/hotend shroud there is plenty of clearance on the Ender 3, I don't take...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

I wanted a minimal 2 pass bed leveling gcode specifically for the wonderfully simple Gulfcoast Robotics 3 point y carriage. This runs to three points (at 120mm/s) with pauses between. Auto home, left front, left back, right center, (repeat all 3),...

**important** This code has been specifically made to be compatible with the popular Creality Ender 3 series of 3D printers (ender 3/3pro/3v2) but it can also be used for any printer with a square build surface of similar dimensions (235×235mm) but...

Gcode pour Ender 3 stock pour tour de temperature Layer: 0.1 Premiere couche 0.3 Infill : 20% Speed : 1ere couche 20 Coque 25 Top Bottom Et placement 50 Bed : 60 40 ( Gcode Temp40 ) Brim : Avec 10 lignes (gcode brim) sans Brim Retrait : Avec Durée...

A modification to Chris's Basement gcodes loads and unloads filament from a BMG installed to an Ender 3 with stock bowden tube, approximately 40cm in length. Chris's original code won't work on my Ender due to excessive extrusion prevention, so I've...

This is the stock Ender 3 Dog gcode that comes with the sd card, I have found it to print flawlessly with multiple brands of PLA filament rolls. Settings work only for PLA, if you want to print for ABS, you will have to tune temperature once the...

HOW TO MASTER A TEMP TOWER: Run this G-code (or code the STL yourself) and see which temperature yields the least amount of stringing and best overall look and strength. [Check out my calibration guide on Reddit for more detailed tuning...

This is my Gcode for print a big Alien Xenomorph en Ender 3 / 3 Pro (45cm) Scale : 170 % Layer : 0,1 mm Nozzle : 0,4 mm The different parts are place on plate in a way to minimize visibility of support and layer...

... the .3mf file with Cura and edit all settings to your likings. I printed with 0.28mm layer height. The project is configured with tree supports only in required areas. The gcode file should be ready to be printed on any Ender 3, but no guarantees.

... be sure to insert the filament so it appears on the start of the bowden tube. Thanks a lot to the original author @Qualith ! You can find advice on how to change filament here: https://all3dp.com/2/easiest-way-to-change-filament-on-ender-3/

... be sure to insert the filament so it appears on the start of the bowden tube. Thanks a lot to the original author @Qualith ! You can find advice on how to change filament here: https://all3dp.com/2/easiest-way-to-change-filament-on-ender-3/

Compared to my highly modified Tronxy P802, my Ender takes twice as long to level because I have to move it from corner to corner manually. This was driving me nuts, even though I prefer corner levelling my printers with every print. Hence, I wrote...