steven crowder change my mind 3d models

#Features of Core A8 Lite I have never fully assembled a Core A8 Slim, therefore my comparisons with the Slim (20mm) are merely based on its design and issues I have with the Lite. ##Improvements Compared to the stock Anet A8, Core A8 Lite, as...

YMMV, but .4mm makes this whole thing print in under 5 hours and it works OK in my printer, for a final version or one I was going to give as a gift I would probably print at .2mm, it looks nicer.Post-PrintingAttaching the Comb or Rubber Stopper...

I have used my paintball settings in Cura for this. that are the fallowing... Quality layer height: 0.2 Shell wall line count: 8 top layers: 8 bottom layers: 8 Infill Infill density 40% (the upper is better done in 100%) infill pattern: cubic ...

If the pipe is loose inside the clamp with it all the way closed then use the Tightener_Ring parts to make the clamp smaller.Attach the Pipe_Clamp_Tilt by sticking the M3 bolt that is sticking out of the Clamp_Outside_Bottom through it and tightening...

Use this with my dual motor mount X-carriage: http://www.thingiverse.com/thing:497661 Follow instructions for screws and parts from this remix I made: http://www.thingiverse.com/thing:524249 If your first extruder is on the left, reversed side, you...

This is best achieved if you point your camera at a 90 degree angle to the sun and then lock the aperture. My way of doing the photoing :) is to take the horizontal bit first fully 360 degrees. Then the clouds and last the ground. Unless there are...

Some features of my boxes are: - Magnetic stackable - each box is the lid for the box below - Fits both standard and GeekUp Bit set ingredients - All of the standard or GeekUp Bit set ingredients for both base game and expansion fit in the boxes -...

This takes about several minutes on my eight-thread system. ...If you run htop, you will notice that the builds happen in parallel, so the more threads you have on your system the less time it will take.The output will be located in...

If done correctly, the screw should tighten just enough to stop the caliper from moving and your wheel should adjust the caliper as desired.Final word:Frankly, this is my first upload and I had no intention of writing this much. I just figured I'd...

from LarkysPrintshttps://www.thingiverse.com/thing:2843853However, my adaptations are based on the remix by emancarrillohttps://www.thingiverse.com/thing:3713857The idea of the handle comes from Doenne90https://www.thingiverse.com/thing:4046499The...

This is a fairly good representation of a 1915 candlestick phone that hides an Alexa Echo Dot Gen.2 in its mouthpiece, sort of a remix of my own Echo Dot Microphone. Most parts are very similar, easy to print and assemble, and looks fairly good...

This is the ONLY short body that worked well in my testing. Wiring harness for motor You MUST also set e-steps by sending g-codes to printer M92 E980 M500 Videos of Bunny Science in Action https://youtu.be/sX2F7Wkocg8 https://youtu.be/DGNUvuxaZQw...

- STL files will follow soon Used Programs: - ArduinoIDE for the Arduino Mega Pro - Thonny for every Micropython program - FreeCAD 0.19 (with Fasteners Add-on) - easyEDA for the PCB design (KiCAD shall be used in the future as open-source...

However the V1_1 is backward compatible and works also with the original plotclock I printed all parts with my up3dmini with 0,2mm resolution and on fine mode (ABS) Beside of this I used: 3 EMAX ES08A II servos Arduino mini pro Tiny RTC board (has a...

So my solution, 3D print it. Now at least I can replace it whenever I need. The basket and cover consist of the Cover, over the basket, with hole for the hose and seals itself onto the basket rim. The rim, which takes the handle and carries the...

(If all you need is the 1/5 scale dummy engine you can still get his version there.) If you wish to get just my 1/5.5 scale engine remix without the cowl, it is available here: https://cults3d.com/en/3d-model/gadget/carl-goldberg-cub-dummy-engine I...

... it permanent if desired.   Clean up any stringing gently with a heat gun as usual.Bonus - Check out some of my other popular models below:Milk Crate Battery Holder 9V EditionSide Tool TrayControl Knob UpgradeStreamlined 6-Card Wallet 

My version of some of the parts for the pitcheron control Aldi/LIDL V2 foam glidershttps://www.youtube.com/watch?v=wV_AQyFsr84This set replaces the centre 80mm of the wing, creating the wing mount, control pivot Centre sections are designed to take...

They are both quite nice designs, I especially like the spring in the second one, but I felt that both were simply too short for my hands and since they were only available as STL files modifying the design wasn't so straight forward. A 2032 button...

The resources tray and the player trays were perfect, so I left them as-is.One of the trickiest things for me is that my buddy has the 3d printer, so it unfortunately takes a few weeks between each try; this also makes it difficult to test and...

This mounts a Raspberry Pi 3B on the right side under the bed, which makes cable management a bit cleaner. Print the bottom part and one of the tops depending on whether you need a slot for the camera's ribbon cable or not. Also needed: 1x M4 T-nut...

It's my first design made with Fusion 360, so the quality may be questionable, but if you want to use it, go ahead: https://a360.co/2HuXXlo BOM To assemble it, you will need: - 3d printed base - a material with high heat resistance (like ABS/PETG)...

Summer is coming.My office is getting hot.I had a spare 200mm Phanteks PC case fan and decided use it as a desktop fan.I have previously designed and printed some “feet” (https://www.thingiverse.com/thing:4515078) to angle the fan just enough for...

The reason Idecided to come up with my own design, is that I wanted to make a parametric andfree design that can be customized to fit any LED strip, micro-controller, orlampshade, and can be scaled up or down as desired (or as required by...

The model I made will require more supports, and however you orient it when slicing, you're probably going to wind up with scarring from support interfaces because in any orientation that would preserve strength, there are curved edges facing the...

... If you don't think your printer is calibrated enough, cut the models in your slicer into small test pieces first.No brims or rafts unless you know you absolutely need it.No supports.For more loom models, visit my Loom collection on Printables.com.

Or just stick a piece of yellow paper on the back.   My some other things:                <a title="Cap.Am. ...Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"><img...

For further examples of similarly-detailed, high-resolution 3D models suitable for a wide variety of project applications, explore my curated online catalog. A sincere appreciation for your review would be greatly appreciated if you're satisfied...

Here is my collection of 18v parts to use with the TS100. Updated for magnetic latching of the hinge. Feel free to add comments for suggestions and post some makes if you make this. I'd love feedback! This project is ideally suited to someone with...

This was originally a proof-of-concept type project to see if it could be done, and it's my first OpenSCAD project. At the time I designed this, I didn't realize there were so many other customizable bearings besides Emmetts' Gear Bearing, some of...