steven crowder change my mind 3d models

I also have a version of this tube which extends from 50-150mm, for shooting at 1-3x magnification with 50mm lenses: https://www.thingiverse.com/thing:4941924 (it can no longer focus to infinity, though) ## More macro accessories Pictured in the...

Here is the list of the scales available: - 1:40, my original design, not a frequently used scale for modelling. - 1:48, usually known as O-scale. - 1:80, a half of the original scale, some parts, as well as the width of the panels, are engrossed. -...

It is quite strong enough to hold my camera (~ 1.6 Kg) and I wouldn't expect any problems, with decently robust printing up to 2 Kg at least. First, a couple of notes. The photos are of the prototype, and have a few minor differences. The upper...

Here my sexy fanart version of the Jem and the Holograms protagonist Jem, the beautiful pop singer, made as a statue in 1:10 scale. I've created also a star base with stage lighting truss, little lights and speaker to complete the scene. The file...

I use the Flat undercarriage mount weighted with BB's to secure my Logitech camera for timelapses with Octoprint and Octolapse, as it allows me quick positioning at almost any angle. Also please note the "Nut holders. They will accommodate several...

I designed this plane using Autodesk Inventor and Fusion 360, taking inspiration from various aircraft designs and adapting them to fit my specific needs. The fuselage is made up of several sections, each printed separately and then assembled...

The name means "Meuse lizard", as the first specimen was found near the Meuse RiverCheck out my page: https://www.thingiverse.com/RyanTheMast/designs for several more Printable heroes and creatures.Update! CH35C0 <a...

Attach a medium-sized rubber band near the top of the launch axle and attach enough chord to the rubber band to allow pulling the chord back to your chin (about 40 inches in my case). The rubber band helps avoid damage to the launch axle if you...

... Like Nylon. In my case it was Overture Easy Nylon using 0.8 mm nozzle, 0.4 mm layer height. 255C. Temp shrinkage scaling 1.0066 (or 100.66%). ... Knobs were printed on resin printer, they use M6 hex-cap bolts which were glued in with UV resin.

I have designed this air purifier for my network cabinet turned printer enclosure. It uses an activated charcoal mat and a HEPA filter to remove any unwanted organic compounds and ultra fine particles from the printing process.</p><p>It is important...

If you have the proper filament colors, no painting is needed. The assembled model is 225mm tall and is in proportion to my other Jetsons models. Enjoy!...

Love T-Shirts? Then you need to check out steps-per-mm.xyz! It is loaded with a huge range of wearable Parts &amp; Components. Please help support my work here on Thingiverse and on Instructables by using the following affiliate links when making...

The ones that come with the Nashbar front rack are rubber-coated, but still rubbed off a lot of paint on my fork over 6300 miles or so. Add inner tube shims. The Tubus version is slimmer & nicer in this regard (they're metal, so can use less...

(Easy, cheap and fast to order directly from Asia). Soldering iron and rudimentary electronics knowledge required. Wetterkappe: https://www.thingiverse.com/thing:3559140 Weather cap: https://www.thingiverse.com/thing:3559140 Eine eigene Kappe werde...

After the lightshades on our Constructa extractor hood broke again I decided to make my own replacement part. This is it. Printed in transparent PLA. Part numbers it goes by: 00653521, 653521, 8713411212741, 7439647988922. ... According to...

This works with my Amscope microscope. Print instructionsPrint in PLA with 0.05mm layers aka Ultra Detail. The printer must be finely tuned because the threads have near zero tolerance. Screw the lens on two turns then back it off one turn, like a...

My version is from 2021-03. * The adjustable buttstock is [thing:4565145](https://www.thingiverse.com/thing:4565145) by [slykittycat](https://www.thingiverse.com/slykittycat), which is actually a remix of...

... getting soft... Also note that I do also keep the silicone sock on my heater block... At the time of this post, this printer is only used to print other PLA's. --- The heatsink cooling shroud and part cooling duct are remixes from... Thanks! ...:)

Macro Keyboard powered by Arduino Pro Micro with printable relegendable keycaps.Buttons are a remix, I adjusted them to better fit my MX switches.Requirements:- 4x M3 x 16mm Screws (M3 x 18mm also works)- 12x MX Switches- 1x Arduino Pro Micro (5V)-...

- My sensor had very high rolling resistance i.e., really held on to the filament: opened it up to find the the two washers on the fixed bearing were mounted the wrong way impinging on the fixed bearing so it didn't rotate at all. Washers are...

I cut my PEX at 8 feet (96 inches or 244 cm). Using 8' lengths will allow you to string a single 5 meter strip without cutting it between 2 arches. If you want to get use out of every last LED, you can cut the 5 meter strips in half and solder an...

There should be enough clearance, but I chose to adjust my motor pulley in by about 1mm. 6) Undo the other end of the belt from the extruder. Thread the belt end through the x-axis piece and around the idler pulley. Then re-secure it moderately...

This was a replacement part for my brother's motorcycle and it is successfully working inside the engine for over a year now (03/2021) see last picture. Original part number: 59035055144 According to motorcyclespareparts.eu The WATER PUMP WHEEL...

Instructions Entire model has been printed on my PrintrBot Jr. V1 using the following "print" settings in Slic3r: This model was designed to be printed as a modular base station to allow you to print whatever buildings you want and place them...

So I created this remix based on 2 holders and added my own ideas. There are many ideas I also want to play with but the base system is ready #News miniVICE X-Series version that improve some issues and supports both round and square bases can be...

I slid my excess tie length back through the holes to prevent a sharp cut edge. If you like, you can tape over the ties to make the edges less sharp.</p> <p>Gather the parts for the Foot Mechanism. Refer to Assembly guide and glue parts together. I...

This rotating mount (MK1) for transmissive optical elements, was designed during my master thesis project: "Development of Next-Generation Optical Tweezers" and used in multiple motorized optical attenuator setups. It has since been further developed...

Since my upcoming magball effector is largely based on this design, I may update it if there are any improvements that I make from the magball design that I can pass onto this one. Predator Dragon High Flow 5015 Effector OLD.stl has been tested,...

The tolerance on the models is set quite high, as my printer isn't particularly accurate. So you shouldn't have much difficulty. However, if they just won't print properly, you can try editing the joint_tolerance parameter in the Fusion 360 file to...

Check out my other designs here: https://www.thingiverse.com/tonyyoungblood/designs Update: A user requested I make a paper version of the template to save on plastic. I have added U.S. Letter and A4 versions in the files section. Update: A user...