steve model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

...Thank you! Change Log:25AUG2022 — Added model and print files of a 3-point version of the modified MINI-minda-holder for using the SPA with Sparkyman987's Fan Spacer Mod.11NOV2023 — Added .step file of the SPA for MINI/MINI+; added remix description.

It does not need power to work, it is simply a switch that opens when the sensor tip touches a surface. It is probably NOT suitable for a 3D printer bed leveling system because it could touch the model you are printing. If you added a removable cap...

... recast into a new weapon. By Alex Wellerstein, a historian of science and an assistant professor at the Stevens Institute of Technology, in New Jersey. Attributions: -Screwdriver by user DAPE (under CC-By-Sa-Nc). -Demon Core modeled by Szadros.

If you want to use the hardware I intended this to use:Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge)Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

IntroductionMany designs like RC cars and trucks, lanterns, model houses, etc. would benefit if 3D printing could be used to create truly transparent window panes. But as you might know, FDM printing transparent filament per se does not result in...

The models in these STL files are scaled for a 58cm head circumference. (Refer to photo of T800 for how to measure the size you will need to print) Just scale in your slicer software on XY by 1/58*[your figure]. Do subscribe to my YouTube...

Models intended to be part of the numbers node all begin with the prefix MMU.Card Compression Spring: if you have problems with the card compression spring lifting off from the bed, it is recommended you add a skirt of at least 6mm.Assembly...

The stock globe has a vent on the top and there are vents in the model to aid the convection cooling. Is it *really* needed, especially with the converter gone? Dunno so the optional rain cap comes with the caveat of possibly shortening diode...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Dimensions: 510 m × 330 m × 241 m Model scale: 1:3x103 (15cm) 1:8x103 (7cm) References "Lawrence, K. and Benner, L., Radar shape models of asteroids compiled by Lawrence V1.0. urn:nasa:pds:gbo.ast.jpl.radar.shape_models::1.0. ...NASA Planetary Data...

It's worth the trouble to get access to a laser cutter to get cut panels.  The duct is intended to print at a 45 degree angle - the part model is oriented as it is intended to be printed. The duct part DOES NOT NEED SUPPORT. Your slicer may...

I would also suggest allow for extra LEDs in your strips and to slide in your LED strips as you combine a segment to other segments. All in all, I learned a great deal about modeling using Fusion 360 and 3D printing using Slic3r and the Original...

It is essentially based on my first design.If you don't have an AC Infinity T8 or don't want to spent 120 bucks on one just to disassemble it, check out this simpler and cheaper...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Some LED displays (3 digit, common anode, 0.4 inch, row pitch of 12.7mm) -Wenrun 12.7mm LTD040BUE-101A red CA -Wenrun 12.7mm LTD040BAG-101 green CA -SunLED 12.7mm DUY10A3-A yellow CA -SunLED 12.7mm DUG10A3 green CA -Luckylight 12.7mm KW3-401AVA...

Both uploading and downloading a few dozen bricks is a pain :) However you can get all: STL.zip contains all the blocks I made so far STL-sets.zip include multiple brick sets for printing (difficult and not so often updated !) source.zip...

We are presenting a new wind turbine device, that is easy to 3d print, it can be made handcraft once it is viewed it components and how they get assembled in a very easy and intuitive view, This system have several pending patents and the device...

... holes. The decorative plugs are designed to be sacrificial, so if you're going to reinstall the knife strip, just print some more plugs! Check out the humorous remix of this design here: Wall-Mounted Magnetic Knife Strip — Home Decor Spoof.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

... broken and no one is going to fix it. Download files one at a time by clicking Download each time. ### My some other things: Category: 2D Art

... one at a time by clicking Download each time. Or click Download once on the file Girl_Unicorn.rar ### My some other things: Category: 2D Art

 A side note - you also probably should be using my rear PC4m10 jack for your MMU3 https://www.printables.com/model/542409-mmu3-pc4m10-rear-connector The perfect length is one make an even curve downward and the up into the back of the MMU that is...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

Printing Recommended slicer settings: Resolution: 0.1mm - 0.2mm Infill: 10% - 20% Supports: Doesn't Matter Rafts: Doesn't Matter License The "Customizable Arduino Nano LED Candle (2 - 6 LEDs)" model (.stl) is licensed under the CC BY license by Code...

-This current model is built under the assumption that most people will be using this with old tablets (or phones) that they would have thrown away otherwise, so taking a tablet (or phone) off of the top slider isn’t a smooth and seamless experience...

On homemade springs using generic musical wire When it comes to homemade magazines, the models by Thanhtacles are designed to use drum springs unlike the box springs exemplified by their commercial counterparts, for what I assume is the most...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.

IF YOU ARE HAPPY WITH THAT, A LITTLE DONATION WILL BE VERY NICE <3https://www.paypal.com/donate/?hosted_button_id=5F525DYM8GXK4 If you want to do a remix or changes to the design, you can get the Fusion 360 and STEP file here:...