sterilite gasket box 3d models

The ones I own are 54qt (51L), but from looking at pictures of other Sterilite gasket boxes, I think this latch is used on multiple models. It fits pretty tightly (tighter than the original) but it does work well and loosens up a bit over time. A...

Note: If you have trouble downloading this model, you can also find it here: https://www.printables.com/social/55222-tyler/models This is a replacement latch for a Sterilite Gasket Box. The ones I own are 54qt (51L), but from looking at pictures of...

The ones I own are 54qt (51L), but from looking at pictures of other Sterilite gasket boxes, I think this latch is used on multiple models. It fits pretty tightly (tighter than the original) but it does work. A bit of superlube on the posts helps a...

I created a clip for the Sterilite gasket boxes I got at Target, model number 1932. The problem with these boxes is that they sag on the sides, which causes the seal to be ineffective. That's where this clip comes in - it presses the sides against...

Threaded rod supports for the 20L Sterilite gasket box. This design assumes 5/16"-18 rod, and fits the corresponding size nuts to hold the supports in place. ...A step drill is recommended to fit the inner support through the box wall.

Simple filament box from a Sterilite 20QT Gasket Box. Print 2x, these are meant to be used with #8 plastite screw. Mount 2" below the side handle, as shown in the picture. A 12 5/8" long 1/2" round steel rod (or possibly wood) completes the...

The Sterilite 20L gasket containers I have are pretty warped at the lid. ...The amount of force this puts on the clips makes it very hard to unlatch them.This remix adds small wings so one can open the box much more easily.

I broke the plastic hinge on my Sterilite 51 L gasket box which I use for a filament dry box. ... I designed a new hinge to 3D print.

Humidity/Temp Sensor Mount Sterilite 20qt Gasket Box

Link to Sensors I used: https://tinyurl.com/y2r4z6f9 Link to Sterilite 20qt Gasket Boxes: https://tinyurl.com/y6pkhtks Printing Directions: (see plate photo) - Faceplate placed flat and should be printed with the face on the bed. (you may have to...

Link to Sensors I used: https://tinyurl.com/y2r4z6f9 Link to Sterilite 20qt Gasket Boxes: https://tinyurl.com/y6pkhtks Printing Directions: - Faceplate placed flat, should be printed with face on the bed. (you may have to free up tabs gently with a...

Customized version of http://www.thingiverse.com/thing:743280 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=743280 Should fit Sterilite 20Qt/19L Gasket Box. ...In Canada, these are available from Walmart.

http://www.thingiverse.com/apps/customizer/run?thing_id=743280 Should fit Sterilite 20Qt/19L Gasket Box In Canada, these are available from Walmart Instructions Using the following options: backlash = 0.5 template_bottom_width = 100...

I remixed MrPTrog's lid clips by opening the angle of the top part a little, as my new 20 qt / 19 l Sterilite gasket boxes might be a bit taller and were causing that version clip to crack at the upper joint (maybe also related to PLA vs PETG or...

I use Sterilite 19324306 20-Quart Gasket Boxs with Blue Aquarium Latches to store my filament. I use loose bead desiccant, so I wanted a tray to keep the spools out of the beads. Tray prints in two halves that snap together with a tab/slot. ... 6 Pack...

I store my filament in Sterilite 19324306 20-Quart Gasket Boxes, which feature blue aquarium latches that secure the contents. Since I use loose bead desiccant to keep my spools dry, I needed a tray to prevent them from getting buried under the...

Great fit and durability printed with PETG 0.4mm nozzle, 0.2mm layers.Print advice:Durable filament like PETG or ABSAdditional perimeters for strength (example printed with 4)25%+ infill (also for strength, perimeters more important)Supports required...

Organize your filament spools in your dry box (specifically for Sterilite 32 Quart Clear Plastic Stacking Storage Container with Gasket Lid) using this dual-rod storage solution! You'll need 6 nuts, 4 rods, 1 joint, 1 coupler, and 2 (optional) rod...

... and created this box. For my dry box, I used the design from https://www.thingiverse.com/thing:1372828. My desiccant box and dry box work perfectly together. ...I also made a filament dryer using https://www.thingiverse.com/thing:2876045.

Dry box round washer - this is for the outside of the box, covering screw heads. And two more types that might be useful: 1. Dry box bracket washer full - same as regular but with no hole in the middle. 2. Dry box small round washer - an...

Replacement latch for the Sterlite clip boxes with the clear lids and light blue latches. Printed in PLA with a .4mm nozzle, supports only under the two side bumps (painted support blocking in PrusaSlicer across rounded latch edge), and .2mm layer...

I have the 54 and 32 quart Sterilite containers that I use as dry boxes and wanted clips for the ends. I noticed the gasket on the ends wasn't getting compressed much at all. These have helped quite a bit and can be used on the sides as a replacement...

Damp-rid container that fits perfectly into this Sterilite drybox design: https://www.thingiverse.com/thing:2929701 Fill with silica gel, damp-rid, sieve, or other desiccants. Although air gaps are a bit large, they will effectively contain the damp...

It holds 3 spools, and all you need are a few basic supplies: Superglue, two prints of the SteriliteHolder.stl file, one Sterilite 20Qt gasket box available everywhere - target.com/p/sterilite-20-qt-gasket-box-clear-with-blue-latches/-/A-15066036,...

The outer section of this design is flat, unlike the original Sterilite model which has a steep overhang. Even with tight settings, the support can still cause issues, so I added more material to create a flat base and curved sides. This makes...

I crafted this holder specifically for attaching a hygrometer to the lid of a Sterilite 20 Quart Gasket box. I opted for some ultra affordable (yet relatively precise) hygrometers that I purchased in a pack of five from Amazon. ... This design is a...

I designed this specifically to hold a hygrometer to the lid of a Sterilite 20 Quart Gasket box. I’m using some ultra cheap (but fairly accurate) hygrometers that I bought in a 5-pack from Amazon. After printing, line it up in the corner and mark...

Compared to my initial attempt, this is a far more user-friendly filament dry box system using Sterilite 20qt storage boxes. No longer must I remove all spools just to replace one. For the filament caps, see my previous version here:...

Compared to my first attempt, this is a much more user friendly filament dry box system using the Sterilite 20qt storage boxes. No more removing all the spools just to change out one.</p><p>All parts print without supports in the orientation...

This is a gasket for the Uno Card Box https://www.thingiverse.com/thing:5850150. Print using TPU. ... I modeled this for 1 mm height, but you may want to vertically scale it to be just a tad thicker for a tighter squeeze, which will ensure greater...