stepper motor fan 3d models

After installing the TMC2208 drivers, the filament feed stepper motor began to warm up. ...Installed a fan for cooling

Small and lightweight solution for the steppers with a 30.5mm hole pattern and a 30x30x10 small fan. Can be used on any motor to cool it down. ...Didn't try it

I designed this detachable fan mount clip for stepper motors because I needed a way to secure a fan without using cable ties or any semi-permanent solution. This design makes it easy to attach and remove the clip as needed. This clip is specifically...

Made this fan mount clip for stepper motors as I needed to attach a fan and didn't want to use cable ties or anything that's semi-permanent. This clip style is easy to attach and detach. For 40mm fan. Can be adapted to smaller fans, I'll probably...

To accommodate standard 40mm fans, simply combine the direct mount and spacer components. For added stability, wrap a rubber band or similar securing device around the retaining tabs. ...This setup performs exceptionally well on the GEETECH A10M with...

Whether you're using the original Anycubic stepper motor fan or opting for an effective but pricey Noctua 50x10 or 50x20, just choose the right fan adapter. I suggest this 40x40 Noctua Fan – it's like a Rolls-Royce! Or, if budget is a concern, go...

This is just a simple 40mm fan mount for NEMA 17 stepper motors. ...First snap it on to the motor and then attach the fan, this will lock it in place.

I encountered a problem where my stepper motor was overheating after I installed it inside the printer, so I came up with a design for a fan bracket that would provide some much-needed cooling.

This is a Remix of NeverDun's Half Stepper Fan Mount, I Wanted a Simpler Solution for My CTC Dual Printer, So I Simplified It and Made It Fit, and Also Included 2 Fan Covers So Both Fans Will Match; There Are Now Over 20 Prints Done with No Failures....

... on a Redrex Nema 17 motor with excellent results. PLA is suitable since the motor maintains low temperatures even when the fan is running. ...If your motor becomes excessively hot, consider reducing the driver's voltage or using ABS or PETG instead.

Shroud designed specifically for stepper motors, featuring a convenient sliding gate to connect stepper wires seamlessly. ...Revised on January 3rd, 2018, with enhanced fan clearance and an enlarged gate cover for a snugger fit.

Improve your Nema stepper motor's temperature with this fan print! Designed for 42x42mm motors and using a standard 60mm fan, support material is not required. Attach the fan with wooden screws or double-sided tape, then mount it onto the motor using...

Upgrading the Stepper Motor's Cooling System Is a Straightforward Process That Anyone Can Accomplish. Amazon Offers a Wide Range of Blower Fans, Including the WINSINN 50mm Blower Fan 5V 5015, Which Should Fit Perfectly on Your Printer. The WINSINN...

Made to attach a 40mm fan to and slide on over with space between the fan and motor itself. Using a USB 40mm 5v fan is doing the trick for me. I used <a...

I aimed to design a straightforward fan shroud for the Nema 23 motors on my Taig milling machine. This creation doesn't demand any support and utilizes merely 45 grams of filament. It does necessitate four screws. I opted for 1/2 inch long #4 screws...

Z Stepper can get hot when doing long Prints, this is an easy upgrade to keep the stepper cold. Amazon sells them (WINSINN 50mm Blower Fan 5V 5015) or any 50x50x15 blower should fit. they also sell them with USB so no wiring needed. attach blower...

Z Stepper can get hot when doing long Prints, this is an easy upgrade to keep the stepper cold. Amazon sells them (WINSINN 50mm Blower Fan 5V 5015) or any 50x50x15 blower should fit. they also sell them with USB so no wiring needed. attach blower...

Hello this is a stepper motor Fan mounting cover for the Labists X1 and other You can use your existing screws from your old cover The Fan is 40X40X20 side blowing fan 12V I used 20mm x 3M nut and bolts to mount the fan Use at own risk

I was fed up with my CTC making a vibrating noise while switched on. I created a new design and used rubber washers on the bolts to mount it through the 20mm hole next to the pre-drilled screw holes. I had to redesign the throat at the end since I...

The Stepper Motor boasts a compact footprint measuring 42 millimeters by 42 millimeters, providing a solid foundation for precision control and reliable operation.

An upgraded Ultimaker extruder stepper motor cooling fan shield design is created to provide a more effective heat dissipation solution. The redesigned cover significantly reduces thermal buildup on the motor and nearby components, thus preventing...

For this project, I used the 40mm fan (available on Amazon at https://www.amazon.com/gp/product/B009NQLT0M/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&), which features a cable insert to lower its speed from 4500 to 3700 RPM, significantly reducing...

UPDATED: 17 August 2021 DO NOT PRINT WITH SUPPORT Hello This is a stepper motor cooler for a Labists X1 X Axis, should fit other variants too. Its pretty deep holes so you will need a long star point driver, but you can use the same screws as your...

This was created to allow for the inclusion of a heat sink. The heat sink I used was approximately 12.15 with thermal tape. ...I used some foam and electrical tape to get the tension right and seal up gaps.

This was created to allow for the inclusion of a heat sink. The heat sink I used was approximately 12.15 with thermal tape. ...I used some foam and electrical tape to get the tension right and seal up gaps.

To make it compatible with Anycubic i3/mega printers that have stepper motor driver fan ducting, I rotated the mounts 90 degrees to save precious space. It was a challenge, but the end result is well worth it! I printed this design on my trusty...

The duct protrudes ~15mm from the back of the motor (not including the fan thickness). To make it, print one stl as is, no supports or rotation required. I used ABS with 0.3mm layers, but other filaments and settings will work. Use screws or bolts...

The duct protrudes ~15mm from the back of the motor (not including the fan thickness). To make it, print one stl as is, no supports or rotation required. I used ABS with 0.3mm layers, but other filaments and settings will work. Use screws or bolts to...

Mount motor fan for 17H249-02S. Fasten with 4 bolts only. Secure in place quickly and easily. ...Done!

... 2mm thick heatsink. Generally speaking, when a stepper motor is so hot you can't even touch it, there's probably too much current running through it. ...Checking your board for options to dial back power could also help resolve the issue right away.