stepper motor dampers 3d models

I couldn't find a stepper motor damper on Thingiverse so I designed this. note I haven't printed it yet. ... print soft tpu in tpu and print hard pla in pla

Hi everyone, I'm TPU stepper motor damper. This project is designed to make your printer extremely quiet, allowing me to print day and night without disturbing anyone, even if my printer is located near my bed. I created this so I wouldn't have to...

A damper designed for NEMA 17 motors is employed in 3D printers and various CNC machines, minimizing vibrations to ensure smooth and silent performance.

Here's a 3D model of the renowned NEMA 17 motor damper. ...I swiftly scoured the internet for an existing model but couldn't find one that met my needs, so I took matters into my own hands and created it myself.

... the part is just 2mm thick. ...I've already tried this on an Ender 3 with pressed-on pulleys and printed with TPU - it didn't throw off the belt alignment too badly. You'll likely need longer screws when attaching these between the frame and the motor.

I bought some stepper motor dampers for my Creality Ender 3 3D printer but they wouldn't fit because my stepper motors have press-fit pulleys which are hard to remove. For the Y-axis I made this spacer so the damper can be used without altering or...

Ender 3 V2 Y Axis Stepper Motor Damper Mount Stepper Motor Mount for the Y Axis to reduce vibrations and quiet your prints. This reuses the Ender 3 V2 Y Axis Stock Screws to mount the new motor mount. Most dampers come with M3 screws anyway. The...

I bought stepper motor dampers for my Creality Ender 3 3D printer but they didn't fit because my stepper motors have press-fit pulleys which are hard to remove. For the Y-axis I made a spacer so the damper can be used without altering or vandalizing...

Vibration Reduction Dampers for NEMA17 Stepper Motors =================================== Install these dampers between your X and Y stepper motors and motor brackets to minimize noise and vibrations. Other vibration reducers are available on...

A sleek solution to quiet the hum of noisy printers, this innovative vibration damper is designed to seamlessly fit onto Nema 17 stepper motors. ...Crafted from durable TPU, it's printed with precision and placed between the motor and its mount,...

This component was engineered to adjust the ANET E10's base height following the installation of a damper on the Y Stepper Motor.

I previously tried using other designs from Thingiverse that mounted the stepper damper on top of the motor but found them to be problematic. ...They either obstructed the bed, fitted the stepper motor too tightly and defeated its purpose, or introduced...

... ...I've added some space to accommodate a bracket from http://www.thingiverse.com/thing:2886101 - that's where the magic happens for the damper installation, and you'll still need the Ender_3_X-axis_mount_plate for it all to come together seamlessly.

I didn't find any part included with my Anycubic Chiron printer to attach the Damper, so I created one myself. The custom-made piece matches the original part provided by the manufacturer, except for an added space that allows the band to fit...

This model enables mounting a stepper motor damper on the X axis, provided the motor features a press-fit pulley that cannot be removed without risking damage to the motor. Printing a simple stop flag or a mount for an M18 sensor becomes possible,...

Same as original but less filament, less printing time !

Follow most of the directions on A-make-designs video and install this part on the back of the motor mount (where the x-axis stepper motor originally went).There are only two holes on the Bolt Spacer. The other two screws are not required, as the...

Dampener: https://www.amazon.com/gp/product/B083JTC6JJ/ref=ppx_yo_dt_b_asin_title_o00_s01?ie=UTF8&psc=1 Disclaimer: If stepper motors not properly calibrated you could print this and it would end up being just barely too big for the 42-40 and the...

I also increase the size of the recessed area as the belt was not properly aligned with these dampers I bought: https://www.amazon.com/dp/B083JTC6JJ/ It fits perfectly now, and if the recessed area is too marge and the motor sits two far into the...

... If someone volunteers to print it and provides feedback, I'll be grateful!\r\n********************\r\n\r\n**** UPDATE ****\r\nAfter further comments about belt clearance, I revised the design of the lower screw support in [ender_x_damper_v5.stl].

I tightened up some loose ends, such as swapping out the bulky bolts for ones that aren't needed anymore, and made sure everything plays nicely with the dampeners.

The motor mount is modified to enable use of the damper. ... Update 5/12/2018: + Version 2 Implemented

Print this and add an extra damper to the back of your y-axis motor for enhanced stability. You'll need to modify the rear left arm of the Y-Axis build plate bracket using a Dremel tool or a scroll saw to provide additional clearance. Additionally,...

Print with PETG or ABS (PLA may overheat near the stepper motor): Print parts: 1x Mount (review the filename for one of three versions) 4x Hex Cab (enhances appearance when installed) Other materials needed: 4x M8x25 screws (millimeters)

MOTOR LENGTH 34 MMMotor length: 34mmDiameter of axle: 5mmVoltage: 12VThe front shaft length: 24mmSize: 42mm * 42mm * 34mmHolding Torque: 2.8kg.cm Scope: 3D Printers, Monitor Equipment, Medical Machinery, Textile Machinery, Packaging Machinery, Stage...

This version has been specifically designed for users who have stepper motor dampers installed. To prevent collisions between the y carriage and the motor, I relocated the motor 3 mm to the right. Additionally, I made a modification to the cable...

Affordable Chinese vibration dampers designed for NEMA23 stepper motors, available through Banggood. I have recently changed from using Fusion 360 to FreeCAD for enhanced control over my files and reduced downtime due to errors by Autodesk. ...The...

So, I designed motor mounts that allow you to install the stepper dampers without the stepper motors colliding with the PCB. You can use the original bolts to mount the motor mount to the printer body and just need six additional bolts (M3) to...

Remix from ZoltanKi: https://www.thingiverse.com/thing:3666581 ZoltanKi's original design has been enhanced with lighter parts, providing easier access to the grub screws on the toothed pulley, and a snugger fit for the damper collar.

It is designed to work with a bed wire strain reliefs (https://www.thingiverse.com/thing:2920581) and a vibration damper on the back of the motor. The assembly doesn't require long screws, standard screws are sufficient (M3 4 / 6 / 10 mm). 2 pieces...