sten mk3 3d models

I was inspired by https://www.thingiverse.com/thing:3504682 and made similar changes to the stock MK3 (without the S!) idler door with some additional changes and cleanup. Modifications compared to stock MK3 idler door: - Slide in holes for the...

Update 09/12/18 - I've added another version of the camera mount for the MK3 with the R3 extruder. This one is longer and can be used on other printers as well. I also tightened up the fitting to minimize wobble and make it more stable. Update...

Prusa I3 MK3 Corner Enclosure - Ikea LACK Table The top corners of this enclosure include brackets that allow you to use the original screws that came with the lack table. The second bottom table is screwed to the legs through the bottom corners...

Designed by our engineers using only the finest sources of [Gummy Bears](https://www.thingiverse.com/thing:1142284/) and [Knobs](https://www.prusaprinters.org/prints/16129-mk3-lcd-knob-3-wing/), our Gummy Knob will spark joy for years to come. ...

A compact, fully 3d-printed reverse bowden setup compatible with the MK3 or the MK3 Bondtech extruder upgrade.I designed this after trying out PC4-M6/10 connectors, which I didn't like for the following reasons:Straight PC4 connectors cannot be...

... stepper motor. The lock system (a ring-type design, shown in red on the picture) features four special slots for easy disassembly. Use a flat screwdriver...\r\n\r\nThe final version has been thoroughly tested and mounted on my Prusa MK3 (picture)

A very simple Extruder pointer for the Pusa mk3/s. I use it with three 8x2mm disk magnets. ...And I uploaded three different hole sizes so depending on your printer you can achieve a good press fit.</p> <h3> Print Settings</h3> <p><strong>Printer...

A custom filament guide designed specifically for the Prusa i3 mk3 3D printer model is now available. This innovative guide also fits seamlessly with the Mk2 and Mk3s variants, making it an excellent addition to any print enthusiast's collection. To...

This spool holder for the Prusa MK3 frame uses a single 608 bearing to minimize feed resistance. Drop the bearing into the hat & push down firmly to seat. Drop an M8 nut into the bottom of the axis & get it close to seated, then insert an M8 screw...

I gathered motors, wires, rods, bearings, and other parts from the printer and set out to build a Pretend Prusa MK3. I'm using a clone Einsy board and a frame sourced from Ali-express. Several individuals have requested the LCD front for their...

I made this lighting kit for the MK3 because I bought a new lens to film the printing. The macro lens needs a lot more light when the aperture is set high (required to get a decent depth of field). There are a lot of files for this project, I...

I was excited to test the TechnoSapienDesign MK3 Filament Guide as an addition to my Prusa printer, but I wanted to see how it would perform with an oval opening instead of a traditional circle. This guide prints in two pieces that snap together...

Support bracket for the MK3 with the new Delta PSU. This is used when removing the PSU to make an enclosure for printing things like ABS. (Power supplies don't appreciate the heat like ABS filament does!)</p> <h3>Print...

I liked denos' TUSH remix https://www.thingiverse.com/thing:2537713 on my haribo and bear, so used his onshape link to make one that fits my mk3 clone frame. ...Included a copy of his side for convenience.</p><h3>Print...

You can attach it to 30x30 extrusion and attach pi camera to the bed for great timelapse. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 20 Filament: Prusament PLA Galaxy black ...

This spool holder for the Prusa MK3 frame uses a single 608 bearing to minimize feed resistance. Drop the bearing into the hat & push down firmly to seat. Drop an M8 nut into the bottom of the axis & get it close to seated, then insert an M8 screw...

I bought a roll of filament with a 2cm hole in the middle, so the mk3 spool holder couldn't take it. I looked all over for a thinner one, but had to make one myself. This is my first try designing something :) I have only tried printing it with 40%...

I created this lighting kit specifically for the MK3 because I recently acquired a new lens to capture high-quality footage while printing. To achieve a decent depth of field, the macro lens requires significantly more light when set at a high...

This is a mounting structure to mount a Logitech C270 camera to the front of a Prusa MK3/s. There are two arms that slide onto the underside of the heated bed structure and a cross bar on which the camera is mounted via a mounting block. The camera...

Hello everyone, I'm here to introduce my Remix MK3 platters for DiscoEasy. It consists of 4 angles that align with the old plate before you secure your 4 screws from the heating plates with springs in place. For those curious, yes, the trays do...

I've included the original authors STL so you can grab everything you need right here, it is 100% unchanged GSLV MK3 Specs (https://en.wikipedia.org/wiki/GSLV_Mark_III): *43.43m tall *4m Diameter Core *2x S200 Solid Motor Boosters @3.2m each...

A compact, versatile tool holder designed specifically for the Prusa i3 Mk3; conveniently holds the tools included in the printer assembly kit or accommodates your own tools. Mounts securely with three spare M3x10 screws directly onto predrilled and...

I've included the original authors STL so you can grab everything you need right here, it is 100% unchanged GSLV MK3 Specs (https://en.wikipedia.org/wiki/GSLV_Mark_III): *43.43m tall *4m Diameter Core *2x S200 Solid Motor Boosters @3.2m each...

I designed a spool holder with a 2cm hole in the middle because my mk3's stock holder couldn't accommodate it. After searching everywhere for a thinner one, I decided to create my own. This is my first time designing something from scratch :)\r\nI...

But, I wanted a clip that was always "right there when I needed it."This clip securely snaps onto the top bar of the i3 MK3, and a 1.75mm filament pops into the clip with a satisfying "snap." Simply pull the filament up to remove.Edit: As other have...

This spool holder for the Prusa MK3 frame uses a single 608 bearing to minimize feed resistance. Only the "hat" requires supports - the other parts can be printed on their sides. Drop the bearing into the hat & push down firmly to seat. Drop an M8...

This is based on Prusa mk3 Einsy - Frame brace from Sendeva. ...I have added some chamfers, short by 12mm so now it is flush with Einsy box.</p><p>Print with 5 perimeters, 10 top, 10 bottom layers or so to achieve some stiffness.</p><p>You will also...

I had trouble finding a camera solution that suited my MK3, so I tried designing one myself but didn't like the result. I then decided to print other people's designs and see if any of them caught my eye. After some searching, this is what I came up...

This is my remix of a Prusa MK3 Toolholder, tailored to fit my specific needs and favorite tools. The holder features 4 strategically placed spots for hex wrenches, making them easy to access when working with tight spaces or complex projects. ...You...

This display cover is specifically designed to fit on the Prusa i3 Mk3 and does an excellent job of shielding the screen while also blocking any light emitted during late-night printing sessions. The design perfectly complements a dial created by...