steiner dbal i2 3d models

This is a fan duct specifically designed for Greg's extruder, fitting a 50mm fan to ensure efficient airflow and cooling during the 3D printing process.

We needed a fan mount and duct for our x-carriage that was short enough to accomodate for our j-head. ...We are proud to present to you "The elephant"!

Screws are now a thing of the past - ditch them completely! ...Simply yank off the worn-out clamp and slap a shiny new one into place.

These are simple power supply unit (PSU) holding brackets specifically designed for the Mendel. They offer a more aesthetically pleasing appearance compared to cable binders. ...To assemble, print two sets and position the PSU between the two M8...

The mount system is designed for use with a 50mm thick power supply, such as this one: http://bit.ly/18XYyUx. It features three brackets that attach to threaded holes in the power supply. Many Chinese power supplies have similar designs. For...

The Prusa Mendel support accommodates two switches; one labeled 'L' for light and another 'F' for fan. Alternatively, a switch can be placed without any letter. The support is 34 mm wide. ...Follow instructions to buy rocker switches...

The z-axis end stop consistently finds itself in the wrong place, necessitating an excessive amount of time-consuming effort to bring the machine back online. To rectify this situation, I have taken steps to guarantee proper positioning by installing...

In order to easily tension my Y belt without having to disassemble the machine, I identified two components close together and combined them. Since the original part was a DXF file that couldn't be edited, I recreated it from scratch using pure SCAD....

This is a remix of kdmshark’s E3D Extruder Setup - Prusa i3, published on Jun 14, 2014. The original design can be found at http://www.thingiverse.com/thing:363307. This new version adds necessary space to host a LJ12A3-4-Z/BX inductive sensor for...

To install, use two 608 bearings and an 8mm smooth rod along with M6 bolts & nuts, plus 4-32 screws & nuts. No disassembly of the threaded rod frame is required. Tighten the belt to your desired tension then secure at the preferred angle using...

Customized version of https://www.thingiverse.com/thing:658691 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=658691

I left the diagonal rods for my printer long and decided to mount the spool holder on them, so I modified this to accommodate a rod that passes through at a sharp angle. Pictures will be added once printed. ... EDIT 10-31-18: A new version has been...

The support, with a width of 32 mm, is specifically designed for compatibility with the Prusa Mendel frame. For acquisition purposes, consider purchasing the USB panel mount connector through eBay. ...To install, print the support and secure it to the...

Directly attaching to the extra/endstop-holder.stl, this part rotates a mechanical endstop by 90° (in the z direction). I discovered that rotating my y-axis endstop was necessary for it to engage under the heated build plate, touching the aluminum...

Check out this updated version of the thing at Thingiverse: http://www.thingiverse.com/thing:28436/#files. ...The modification was made on August 3, 2015 and it includes an addition to the base board for a non-conventional RAMPS setup.

A support mount, designed specifically for typical HP VGA cameras, allows remote monitoring of printing processes through a USB connection.

Secure the accessory firmly to the printer by wrapping a sturdy zip tie tightly around both the device and the attachment point.

The fan mount and fan cone are specifically designed for a 50mm fan, providing a secure fit and optimal airflow.

To use your printer, begin by attaching the two handles provided, then slide them onto the power supply. ...Finally, affix the assembly to the rear of the printer.

I redesigned the structure to enhance its strength, as there were no spaces between bolts and the NEMA motor fit precisely inside. ...To construct it, print two components in the same orientation as the STL file suggests, while using the previous U-bar...

Assemble the entire structure by printing and combining all three parts. To do this, you'll need the following components: one 40mm fan rated for 12V, four M3x20 screws, and eight additional M3 washers. The fan will also require four M3x16 screws or...

Utilizing the metallic plate accompanying the E3D clone nozzle assembly.

This design targets the C7-connector type and power switch. Separate files are available for the C7-connector and switch. ...Due to its parametric nature, this design can also be used for various other purposes such as switching light bars, and adapting...

I've just installed a versatile mounting system that allows the user to attach the device directly to their workspace, eliminating clutter and saving valuable desk space by simply screwing it into place on their existing work surface.

<p>I wanted to be able to tenson my Y belt without haveing to pull the machine apart to replace parts.<br/> I found two things that where close and basicaly combined them.<br/> Since this part was orriginaly a dxf that was extruded and I have no...

A precision adjustment was made by adding a designated area for a touch sensor, while also upgrading the stepper mounting system with strategically placed slots to securely manage wiring. ...Version 3 and version 4 mounts are now available for use with...

This is a Adapter to use the standart Wades extruder with a 4mm bowden tube (for 1.74mm filament). There are two vaiants: one to use m5 nuts and one for m4 nuts. Old: This is a first rweork to use Wades-Bowden adapter combined with an Extruder...

This combo power switch and plug combo from Amazon features exceptional support, holding firm against any combination of use. ...Designed to withstand even the most demanding applications, it securely attaches a light fixture over a small portion,...

<p>I had to scale it to 101% to make it snap. Also I had changed it to use 1x M6 screw and nut. ...This fits nicely on the right side of the printer (front-right) and uses a good angle and height.</p>