steelseries 61298tx 3d models

Steelseries hub (61298TX) holder i printed with PETG and it took around 4 hours. (tight fit)</p><p>I choose PETG for durability to put hub in this holder</p><p>Used 0.2mm line height with supports. ...But maybe you can print without ;)</p>

The emblem representing the brand, SteelSeries ---

A SteelSeries-made mousepad, sized at 320 x 270 x 3mm, is offered for your gaming convenience.

SteelSeries Apex 350 Keyboard.

SteelSeries Apex 350 Keyboard.

SteelSeries Stratus Duo Stand

Headsetholder Wallmount with Steelseries logo

SteelSeries Siberia Elite Prism Headphones

Wheel design for steelseries rival 110 mousse. ...Color recommanded : White.

A custom headset clip for my Steelseries Arctic 5 headphones

customisable printable blank nameplate for SteelSeries Rival 300.I do not own this design.

Under desk headphone holder specially design to fit perfectly Steelseries Headphone

It's just a headphone Steelseries stand to put under your desk.

To storage loaded SteelSeries H-Wireless / Siberia 800 and similar (Nokia) batteries

An Xbox 360 controller style grip for a Steelseries Stratus Bluetooth controller. Fits very snuggly, and is very comfortable! Note: This is NOT for the Steelseries Stratus XL. ... This took a while to make, so any tips are welcome!

SteelSeries Unveils Enhanced Arctis 5 Headphone Holder with Increased Durability; Latest Upgrade Now Available for Immediate Use.

SteelSeries ignites the gaming sector with groundbreaking creations, crafted precisely for esports and devoted gamers worldwide. High-performance headphones, the SteelSeries Siberia Elite, amplify your immersive experience. Optimized mice, the...

This keycap is meant to be printed, painted, and then cast in resin for the final keycap. ...This keycap has the logo for Steelseries.

Keycap for Steelseries M800 Keyboard with QS1 switches will probably do more mounting system taken from: https://www.thingiverse.com/thing:2191226

This headset holder is meant to be screwed with a M5 countersunk screw. ... The SteelSeries logo is here only because i use this to hold my Arctis 3 so this holder is not a real SteelSeries product and will obviously fit for any headset brand.

I made Steelseries Arctis 5 prototype design in order to make my Steelseries Arctis 5 transport box. If you need, you can check it out! The prototype turned out quite accurate, it has some flaws but works great for me. ... -...

'steelseries_gamedac_holder_raised.stl' is raised up a bit and angled at 30deg so it is easier to see the display while sitting at my desk. If your printer can close the circles and do the bridge supports are not needed. ***...

This is an easy to print holder for two Nimbus Steelseries controllers. ...Print two of the controller plates and one each of the rest and simply use contact glue to glue them together.

... the already glued areas. I salvaged some screws from an old RC helicopter I had lying around and repurposed them for this DIY project. My intention is to help others who may be facing similar issues with their expensive Steelseries 800 gaming mice.

SteelSeries Arctis 1 Wireless monitor dongle mount. Assemble using two countersunk M3 screws and nuts. Cable connector fits in snugly, no need for glue/tape. The monitor adapter fits EIZO FlexScan S2202W (flat top, 44.5mm deep). ...Use double-sided...

This is a small tray that gets screwed into the underside of a table or a shelf, next to the edge, for conveniently mounting the SteelSeries GameDAC. All ports remain accessible. Designed for screw mounting, but Command/Power strips might also work,...

Stand fits a SteelSeries Nimbus game controller designed for Apple devices and Apple TV. IMPORTANT NOTE: Prints at 5.4cm in width, measured from left to right, as viewed from the front side of the dock. ...Possible compatibility exists with Xbox game...

This is a holder for Steelseries headphones Chatmix dial. The mounting point will print solid and will need to be drilled out by the printer to fit the appropriate mounting hardware you'll be using. ...Can be mounted to any solid surface, desk, wall,...

Bracket and horns for the Steelseries Siberia v2 headphones Remixed From: Little Horns by Scottland Print instructionsI printed the bracket on edge with supports, but didn't require any for the horns.

This is a straightforward design for a sturdy holder that can accommodate two Nimbus SteelSeries controllers. ...Simply print two copies of the controller plate, along with one copy of each of the remaining parts, and secure them together using contact...