st link 3d models
145048 3d models found related to st link.prusaprinters
Over the years my ST-Link's case got beaten up and I wanted to make a new one.I had some issues with PLA warping on the textured sheet so I also added models and gcode file with antiwarping ears.G-codes are for color print for the logo to pop out
thingiverse
A DIY Solution for Nucleo ST-Link Board Enclosures.\r\nYou can easily assemble this case without using a screwdriver - just snap it together.\r\n\r\nThis case features holes for USB, SWD port, UART port, and LED.\r\nBefore you install the board into...
thingiverse
On every Nucleo board, you can shatter the programmer and craft a standalone ST-Link V2 with RX/TX functionality at your fingertips. I opted to design a compact enclosure to house the programmer seamlessly. It took me precisely three iterations to...
thingiverse
My Solution is to use a protective case that fits snugly around my ST-Link V3.
cults3d
This is housing for ST-LINK V2 (mini) from WaveShare https://www.waveshare.com/wiki/ST-LINK/V2_(mini) Printed with wood PLA. The led lightguide printed with transparent PLA. ...No support required.
thingiverse
I created a straightforward adapter just for the ST Link V2 mini that I purchased because there wasn't one available initially.
thingiverse
The device itself can be found on the WaveShare website: https://www.waveshare.com/wiki/ST-LINK/V2_(mini) Printed with wood PLA, this case is both durable and aesthetically pleasing. The led lightguide printed with transparent PLA adds a touch of...
thingiverse
I liked Puffin's ST-Link V3Mini case [here](https://www.thingiverse.com/thing:3864843), but I had trouble getting it to actually work. Not only were the tolerances far too tight for my printer, but it just seemed to be too short for the PCB to...
thingiverse
Two connectors are included, which serve as holders for jumper cables to prevent mis-wiring of the Nucleo board to the ST-Link. A different connector is required for each type of Nucleo board, and so far only one has been created for the...
thingiverse
A collection of end caps for the popular and cheap ST-LINK/V2 clone. To use these caps you have to remove the black plastic around the pins. There are caps that are meant to be used without removing the pins themselves. The caps actually clamp...
grabcad
Check out http://www.gistroy.ru and connect with http://vk.com/gistroy to stay updated on the latest content. Don't forget to like, subscribe, and invite your friends for support – every action counts! ...Expand your network by adding me as a friend...
prusaprinters
This box encapsulate the ST-LINK V2 mini, if you have soldered cables to it on both ends.It is also compatible with a TTL to USB adaptor of the same size.The box have cable retention. ...This is why I made it, instead of just using shrink flex.I have...
thingiverse
I followed this [guide to make the cable](https://empoweredpeople.co.uk/2020/05/28/tongsheng-tsdz2-what-firmware-options-are-there/), but soldered cables on both ends of the ST-LINK V2 mini. ... See also my [battery holder for Nihola...
prusaprinters
This box encapsulate the ST-LINK V2 mini, if you have soldered cables to it on both ends.It is also compatible with a TTL to USB adaptor of the same size.The box have cable retention. ...This is why I made it, instead of just using shrink flex.I have...
prusaprinters
A colleague requested a DIN-rail mount for his ST-Link V2 Isol programmer in order to ease handling a little.One good opportunity to test a new spring mechanism which I'd like to call the “moustache”. It's not snap-in and fiddling in the spring...
thingiverse
This is a straightforward, compact chassis designed to house the ST-link interface, which can be utilized with a wide range of ST microcontrollers. Please note that this chassis has a very tight fit, so you'll need to carefully adjust settings and...
prusaprinters
<p>Recommended print settings:<br>0.15mm layer height<br>4 perimeters<br>30% infill<br>Probably best to print in ABS/ASA, but PETG seems to be working fine for me.</p><p><br>2pcs M5x8 grub screws needed for mounting</p>
thingiverse
Original: https://www.thingiverse.com/thing:3163349 I have added some guards for sticking out goldpins, and lowered the center extrusion for screw - I got in set a 7mm height brass screw-nut (which is too high for original project). Also I...