squishy turtle by jake 3d models

Both snap onto the backplate by inserting part way raised and then sliding down until they snap into place. The bottom of the part cooling fan housing will be below the CR Touch mount when you insert it. Be careful of your wiring. The backplate...

You still get the diffusion effect without getting too much light absorbed by the diffusor. The diffusion area is 0,8mm thick (z-direction), so 0,2mm layer height is optimal for the diffusors. I HIGHLY RECOMMEND to use a "like new" print surface. ...

This is how Prusa rejects drift caused by the filament and bowden tube when trying to detect the probe contacting the build plate.The “Pullback Move”: Prusa does a small, relatively slow move away from the build plate before retracting. The point...

Since the connector is attached by four legs (two on each side of the board and all four were soldered on my board) plus the center pin, this is not easy and I found it easier and safer to cut the mounting legs, remove the connector, clean off the...

For the uninitiated: the [MiSTercade](https://misteraddons.com/products/mistercade) is an add-on for the DE-10 Nano used with the [MiSTer Project](https://github.com/MiSTer-devel) made by [MisterAddons](https://twitter.com/MisterAddons?s=20) which...

By nature, LED light sources run significantly cooler than traditional lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable,...

Use at own risk, you may have to reprint them later.------------------------------------------------------------------------------------------------------Voron Stealthburner Beta for Creality Spider V1 hotend with Orbiter 2.0 extruder (direct drive)...

This project was started by members of a local RC yacht club. Based on their handmade rudder prototype and measurements (plus a slightly used stock rudder), I produced some CAD models. Currently, I am producing a couple of test prints for them to...

 The device is powered by 5vdc mini USB and uses an array of UV LEDs and a computer fan to lure, capture, and trap flying pests on a sticky glue pad in the base.  Arduino Nano controller allows mode selection between always-on and auto-on at night...

It is not the best, since very little by little it continues to twist, but very little and every so often, not like before. Also, at the end, the thread breaks. More or less to give you an idea, without this I adjusted it once a week. With this I...

Multiply by 10 to get the millimetres, which in this case would be 79,577. Open the project file in Fusion 360. On the “SOLID” tab, click on “Modify”, chose “Change Parameters” at the bottom of the drop down. At the top, there are favorited...

The drive wheel at the business end is geared up by 25:1 to reach speeds of more than 3000 RPM. Pulling the trigger drops the deck onto the feed wheel, and then watch the cards fly!</p><p>This thing is designed so it will fit on a 150mm x 150mm print...

By nature, LED light sources run significantly cooler than traditional lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This solid state design of light emitting diodes provides a more reliable, stable,...

By virtue of reading this, you're currently on the internet and can look it up yo damn self :P Videos and guides for the Ender 3 will translate just fine to the Aquila. Be next to the printer while it does the tuning. I haven't mounted a bed...

PS: All of this inspired by this guy's work (aside of course from Corosi and Rosenthal offerings earlier in the pandemic https://en.wikipedia.org/wiki/Corsi%E2%80%93Rosenthal_Box), particularly when he got to here:...

Previously i also designed this case but i forgot to print the version with the brackets so i decided to make one with these tiny neodymium magnets The nuts are press fitted into the bracket These brackets will hold a 5mm fan to cool the raspberry...

... changes mm/minute</p> <p>M566 values may be a little low. need more testing. These values were tuned by using Kisslicer's wizard. TBD: M593 Dynamic Acceleration Adjustment. ...Preliminary results were no improvement.</p> Category: 3D Printer Parts

The factory sealed, explosion proof fixture is protected by a copper-free aluminum housing with an epoxy powder coated finish.The EPL-LB-50LED-RT-CM is a Class I, Division 1 &amp; 2 and Class II, Division 1 &amp; 2 explosion proof light fixture that...

Here's my attempt at replicating the Infinity Orb from the film Guardians of the Galaxy. In one of the pictures, you can see a side by side comparison of my orb and the orb from the film. I tried to replicate all the hole shapes to the best of my...

You can also speed this up by putting the soap in the fridge.&nbsp; &nbsp; 10. When the soap has set completely, you can push it out of the mold and carefully remove the Prusa stamp.</p><p>&nbsp;11. ...Hooray now the soap is ready and you can wash your...

The factory sealed, explosion proof fixture is protected by a copper-free aluminum housing with an epoxy powder coated finish.The EPL-LB-50LED-RT-CM-DIMM is a Class I, Division 1 &amp; 2 and Class II, Division 1 &amp; 2 explosion proof light fixture...

Saturday night brings another exciting project, this time featuring a twist inspired by Zelda's items! I'm sure you'll love it - don't forget to show your appreciation with a heart! ❤️</s> <|im_start|> assistant On the upcoming Saturday, get ready...

The factory sealed, explosion proof fixture is protected by a copper-free aluminum housing with an epoxy powder coated finish.The EPL-LB-50LED-RT-WLM is a Class I, Division 1 &amp; 2 and Class II, Division 1 &amp; 2 explosion proof light fixture that...

The LED light fixture assembly can be removed by releasing the hand knob and sliding the light and mounting bracket off of the center support while the legs can be collapsed, aiding in deployment, storage and transport. The lamp can be easily...

Take care when pushing both parts closed as the link will easily break, a little sanding of the small chamfered part of the link can help it slip into place without breaking.The case should keep closed by itself, even if the link breaks, but you can...

Do not use a motor for drilling - only drill by hand in order to avoid the material from melting, it will only take 10-20 seconds anyway Now carefully push the light post wires through the little hole in the platforms upper deck, through the center...

The screw is used to guide the insert into the hole, and then I can usually press it in by hand, but sometimes it requires a few taps to seat it. If it does not seem to go all the way in, then I would remove the screw used to seat it, and then...

CAUTION: Again this is an experimental model and although it worked in my case it might not work out as well for yall, if you decide to try it out and figure out a way to make it, by all means, I'd love to see it. In my tests, these a good amount...

The factory sealed, explosion proof fixture is protected by a copper-free aluminum housing with an epoxy powder coated finish.The EPL-LB-50LED-RT-WLM-DIMM is a Class I, Division 1 &amp; 2 and Class II, Division 1 &amp; 2 explosion proof light fixture...

The 5V needed by the external relays can be taken from SONOFF. The logical control of the relays is also done via GPIO pins of the SONOFF. For this, the configuration must be adapted. (Generic 18) See pictures. The 240V power circuit works in...