sprite extruder pro firmware 3d models

The Cerambot Pro Extruder boasts a unique shape, setting it apart from the standard extruder design showcased in Thing 3196872 on Thingiverse. ...**Note that this is not an operational extruder, but rather a precise dimensional model intended for...

The Mosaic clip will not fit the stock Sprite extruder on the Ender 3 S1. This clip fits over the domed feed inlet. You'll have to attach it to the top of the extruder: velcro, adhesive, etc. ...I bonded mine Slicer settings are not important; I did...

Modification for the CR10s Pro Extruder. The connector kept damaging the PTFE Tube. ...Didn't have a problem with my Ender 3, so I adjusted the clamp to fit the PTFE coupling from an Ender 3.

If the stepper motor stops once the print starts, there may be a chance that the current of the stepper driver is too low for the new motor. In this case, you may need to increase the current by turning the screw next to the stepper driver. To do...

Parts required for this upgrade if upgrading a Griffin Pro: 3x M5x15 1x Ultimaker printer bed bed spring (available on Amazon) 1 WINSINN 3D Printer Drive Gear 40 Tooth 8mm Bore Stainless Steel extruder wheel (check Amazon) If not replacing a Griffin...

The extruder body features a break-away support structure that can be easily removed using pliers after printing at a layer height of 0.2-0.3mm and an extrusion width of 0.35/0.5mm.

By eliminating one Extruder, I've found that the Top Plate can shift downward and trap filament at an awkward angle, disrupting flow and pinching delicate wires. ...To avoid this issue, this solution works seamlessly with either the Left or Right...

90 degrees rotation and 30 degrees inclination for using the provided spool holder when updating your Ender 3/Pro with the Creality Sprite Extruder.

So I remixed the model, and opened a whole on the cover, enough for the probe mount not to hit the motor cover.Finally, I wanted to do some cable management for the sprite pro cable, which is known to be prone to fail unless you use some strain...

Files have activated filament sensors you can disable in the printer's screen menu: Uncompiled and compiled files here: https://www.dropbox.com/s/ly59gypivj67fmg/FLSUN%20QQ-S%20MARLIN%202.0.5.3%20STOCK%20%26%20TMC2208%20V2.zip?dl=0 Firmware also...

This remix allows for a Fysetc portable input shaper to be fitted to a Creality Sprite Pro extruder

This protects the base of the ribbon cable at the hot end from twisting to prevent cable break

Really liked the simplicity of the the design, but was a tight squeeze to get it attached properly. ...I adjusted the part a bit so it sits snug around the filament inlet so the bowden tube can properly make contact.

This cable holder is remixed from @prometheusMax 's holder. I just wanted to use a little less filament for it, so remeshed this in Blender with some perforation! I just printed standing up, that way no supports needed. Use a raft or a brim,...

The design of the Stock fan mount is hilariously dumb, not only does it blow from only 1 direction, but the fan is blowing hot air because it's sucking the hot air from the heated bed, it also works like a vacuum cleaner, and sucking stringed...

The 5015 is too loud for me so I went with another 4010. I'm using the same 4010s for the hotend and parts fans now - https://www.amazon.com/gp/product/B07L2WTH7H/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 This is to be used with either the...

Extended the belt clips and added reinforcement to eliminate the weak spot.

This cable holder is remixed from @prometheusMax 's holder. I just wanted to use a little less filament for it, so remeshed this in Blender with some perforation! I just printed standing up, that way no supports needed. ...Use a raft or a brim,...

This is my mount for the TriHorn style duct from https://www.thingiverse.com/thing:5277750 Mounts with a single M3 screw and nut (I originally had a pin that friction fit into the fan hole, but since the way it prints, and the layer lines, it was...

extruder spinner for the sprite , using Taurus V4 cooling duct original cooling mod :  https://www.printables.com/model/511962-taurus-v4-cooling-duct-for-creality-sprite-extrude

Sprite/ender 3 s1 extruder flat cable holder for ender v2

You probably want to assign the extruder with the mechanism attached to the second extruder, so you don't constantly use it when you're doing single-color prints. And you probably also want to use it for the part in the model that uses the least...

Ender 3 pro extruder knob

Extruder knobe Ender 3 Pro

60mm resin-printed ring cooler for Creality Sprite extruders with Volcano nozzles. ...Fits the stock fan mounting points on the Sprite extruder and can deliver quite a lot of airflow with the right fan.

I do not (made) compile this firmware, so please do not ask me for other files, however it's the best firmware I found to My Ender3 pro because is stable and has lots of bugs fixeds... ... So have fun I hope have aided...

Replacement backplate for the Creality Sprite Extruder (comes with Ender 3 S1 / S1 Pro). This backplate allows you to line up the CR-Touch probe with the y-axis of the nozzle. This has solved a lot of bed levelling issues for myself and many others,...

Use this to relocate your filament sensor to the top rail from the standard extruder position when upgrading to a Sprite extruder on your Ender 3 v2 etc.

Heatbreak: https://www.amazon.com/Extruder-Titanium-Heatbreak-Compatible-Creality/dp/B09XJZFHYB/ref=sr_1_6?keywords=sprite+heatbreak&qid=1670846244&sprefix=sprite+heat%2Caps%2C125&sr=8-6 Print settings: Line width: 0.40 Layer height: 0.20 Walls: 3...