sprite extruder pro firmware 3d models

These files are my Marlin 2.0.1 firmware for my BigTreeTech SKR Pro motherboard. I modified them using PlatformIO, then zipped them with 7-Zip. "Marlin-2.0.1 - freshly unboxed - 2 endstops swapped - no drivers installed.7z" This file is used to test...

**Files**: - _base - bolt cutout_: mounts to the base plate, held by the 4 screws meant for the Sprite extruder - _base - bolt cutout extended_: an alternative to the base, added another screw hole that lines up with the hole in the pancake motor...

This is the cable management I used to covert my ender 3 to sprite S1. ...The Rectangular cable tube is so the excess wires going to the sprite extruder can be folded inside.

Firmware for Sapphire Pro from Marlin 2.0.9.2 2xTMC2208 (X & Y) + Bltouch ROBIN NANO V1.2 Once the firmware has been updated, reset the EEPROM -------------------------------------------------- then make the autotune of the Hotend M303 E0 S200 C7...

For the firmware I downloaded TH3D's unified firmware, then edited and compiled it myself so that the bed is probed at equal points around the edge and exactly in the centre on a 3x3 grid. I also added power loss recovery and other minor...

I want to add the new Creality Sprite Extruder to my Ender 5 Plus. The Pro kit comes with a new mounting bracket for the 2020 gantry extrusion. However, the orientation of the belt for the X axis is 90 degrees off. Not wanting to go through an...

## New releases are now based on [official bugfix branch 'bugfix-2.1.x'](https://github.com/MarlinFirmware/Marlin/commits/bugfix-2.1.x) (Marlin 2.1.2) ## [Source @ Github](https://github.com/MirakelPrints/Marlin) ### Marlin 2.1.x firmware for...

This is a cable clip mod (with Threaded Inserts) for the Creality Sprite Extruder Mod used on the Ender3/Ender3 Pro/Ender3v2. The Sprite Extruder has a ribbon-style cable in braided sleeving. This printed STL mod will clip and hold the cable so it...

x switch cover for the sprite extruder stock cover cuts quite a bit off with the new mount so i moved the switch to get the room back tested and its working good

This is a mod to install a Creality Sprite Extruder and a Creality CR-10 hotend on a Creality Sermoon D1. This will also work for Micro Swiss hotend as they have same mounting dimensions. ...BOM and Assembly doc included.

... is incredibly easy to use. To install new firmware on the board: Begin by extracting all files from the zip folder onto your SD card. Insert the SD card into the printer. ...Power up the printer and wait for it to complete the update process.

... To install new firmware on the board, follow these steps: Extract all files from the zip folder and transfer them to the SD card. Insert the SD card into the printer. Turn on the printer. ...Wait for the printer to complete its update process.

This shroud connects to the standard Creality CR10/Ender X carriage Extruder mount plate. ... It is meant to be added on top of the extruder mount. I designed this to be used with a Sprite Extruder without the PCB connector board.

If you get the Creality Sprite extruder, do NOT pull your machine apart until you print one of these!! The mount on the extruder only works for Creality sensors! It mounts on the opposite side of the extruder from the other mount. I revised it to...

This is a Sprite Extruder/Pro shroud that will fit on an Ender 3 v2 using the existing hotend mount, will not work with the breakout board is the mounting holes is where the board would normally be  I have manual spliced and soldered the...

So, I designed this bracket to hard mount the sensor to my Sprite Extruder Pro and also clip on to the bed. How you mount it is shown in the pictures. I printed it in the orientation that it mounts and enabled supports. Its not perfect but...

Creality have not yet officially released firmware however I was given this by their support team. Why they haven't released it I don't know but there you go. Works with BL Touch and CR Touch. May work with 3D Touch too but I am not 100% sure on...

I was tired of problems with 4max pro 2.0 display (bugs, lack of modern features, weird protocol, no official marlin 2.x support), so i decided to replace it with modified https://github.com/bigtre.../BIGTREETECH-TouchScreenFirmware). The display is...

Creality Sprite extruder ribbon brackets for Ender-3. Original extruder ribbon guide replaced with parts 1 & 2 assembled. Part 3 - is bracket on the X-axis, mounted with 2 M3x10 screw & nut (yes, I did holes in plastic end switch mount). Part 4...

Original design wouldn't allow the hot end to move all the way over to hit the end stop if a creality sprite extruder se was installed. ...Modified to only fit in the outer cut out to clear direct drive motor.

This is a mount for the Ender Sprite Direct Drive Extruder. It provides a mount for a BL Touch as well as the Creality filament runout sensor. ... 0.2mm layer height 25% infill Yes supports Probe X Offset: 35.5mm Probe Y Offset: 3.1mm Probe Z...

Stripped out the guts of a microsoft lifecam 3000 made a new housing that mounts to a sprite extruder as a nozzle cam.The slicer image shows the orientation I printed this in with tree supports below the overhang.Once the cam is mounted you will need...

A cut tool to cut a section of bowden tube to match the length of the piece inside the Ender-3 S1 Sprite extruder. Print with high resolution settings and use an Exacto-knife or simlarly small and sharp blade to cut the tube. ... Replaced the stock...

I've yet to see a part cooling fan for the sprite extruder that does not completely block your view from the nozzle so I went ahead and created a design with the fan is mounted on the side of the print head. ... I included the F3D file in hopes that...

This is an adapter to allow the Creality Sprite extruder to utilize a PC4-M10 PTFE coupler. It requires the addition of one M3-8mm screw to hold it in place. This file was created in Tinkercad and the file is public... ...you can modify it here:...

Cable guide for Sprite Pro for Ender 3v2. Mounts to the top of the old extruder motor mount. ... Needed Hardware: 4x M3x8 screws, 4 M3 washers and 4 M3 nuts.

The Rectangular cable tube is so the excess wires going to the sprite extruder can be folded inside.Print SettingsPrinter Brand:CrealityPrinter: Ender 3Rafts:YesSupports: NoResolution:0.20Infill: N/AFilament: Priline TPU Black Notes: Printed with 30...

This is a simple bracket to control the cables for the hot end and sprite extruder on my Ender 3 Neo, cables kept hitting frame. Can mount on left or right side of extruder, whatever give you the best clearance. Needs 2x 3mm x 8 screws. I used 100%...

... (that's how I finished the prototype, drilled some holes and mounted it). This is way more robust of a drag chain mount for the sprite extruder on my Neo Max. Feel free to modify this to suit your needs. ...If you remake, or make, please share.

The holes on the backplate on the original "Ender 3 Sprite Extruder hot end fan replacement with 5015 blower" didn't line up on my Sprite Pro. I moved things around and now things line up perfectly for me. ... Someone asked for a the fan holder...