sprite cr touch mount 3d models

This time, I sliced out the Bltouch/3D touch mount, shifted it out by about 5mm, and inserted a scaled cube in the gap left. Now, it's printing out, and hopefully it will work out okay despite some gaps and overlaps showing up because of 3D Builder's...

This is a simple mount that allows to use the Ender-3 S1 Laser module without remonving the Sprite extruder. ... https://youtu.be/-a9nY-8EYfI

***UPDATE*** Fixed default orientation of STL for easier printing I wanted a BL Touch mount that would easily clip onto my custom hot end cover, as well as hold the nuts in place for easy mounting and removal. Offsets: X:-49, Y: -12 For Z...

Monting fixture for Sagrotan No-Touch on Smedbo soap dish

I remixed this part, so it fits bl touch properly

Remixed it to fit Creality Touch form factor (connectors not located at the same position than BLTouch / 3D Touch)

They prevent deformation of the plastic by spreading the load and ensure everything remains tight in the long term) Use the extruder PCB mount from here: https://www.thingiverse.com/thing:4143992 If you want to run ABL use the stock hardware and save...

A wall-mounted holder specifically designed to accommodate the Oculus Rift Touch Controllers, a cutting-edge virtual reality accessory, is showcased here. The model used for this project was my wife, whose hands were meticulously scanned using an...

I loved the Raspberry Pi case, particularly its touch screen feature, but I wanted to take it a step further by mounting it on top of my Prusa i3 MK3S. Additionally, I needed easy access to the backlight switch located at the back of it. ...To achieve...

I've made the part that the bl touch mounts to thicker, and added a brace. I also created spots for the M3 nut to slip into and stay, this way you dont need to fight with tightening the nut. I've included two versions, one with the nut on top...

... it perfectly, printed both pieces with precision. I assembled it securely with Krazy glue and two small 1/4" dowel rods that were lying around. Then I screwed it firmly into the wall, and now my Touch Controllers are finally off my cluttered desk.

Mounting a Raspberry Pi Touch Screen on a T-slot 4040 is a straightforward process that involves attaching the screen to the bracket and then securing it to the T-slot. The first step is to place the screen onto the bracket, making sure it's centered...

I've designed this stand specifically for my CV1 (the hands are courtesy of https://www.myminifactory.com/object/3d-print-oculus-rift-touch-controller-wall-mount-hanger-42153) - if you'd like, consider supporting the creator behind those hands. ... You...

My Marlin offsets are set as follows: X_PROBE_OFFSET_FROM_EXTRUDER 9 Y_PROBE_OFFSET_FROM_EXTRUDER -38 Z_PROBE_OFFSET_FROM_EXTRUDER -1.0 As always with probes and mounts, be cautious when adjusting these settings. The probe is only about 2-3mm higher...

With the Ender 3 firmware + stock motherborad and the accompanying mounting bracket, my Z-probe offset needed to be -11.4, but it wouldn't let me go past -10, this bracket brought it to -8.X (side note, after upgrading to a SKR Mini E3 V2, my Z-probe...

Compact BL Touch mount for the Ender 3 V2 Initial version (my preference, unless you use the Creality firmware and don't want to update the offset): Offset X = -39, Y = -7 Version with correct offset for Creality firmware: Offset X = -45, Y = -20...

I wanted to reclaim space on my X-Axis, so I figured a 40mm BL Touch fan mount was needed. However, after a few iterations of a static mount, I felt it pertinent to redesign it from the ground up so there was at least some level (no pun intended) of...

This mount is a Remix of https://www.thingiverse.com/thing:3068105 for ANET A8 Adjusted mounting holes for sensor and modified for clear visibility of sensor status (Blue LED) for 3D touch clone from aliexpress...

This is a remix of Skia_MKX's remix of Satsanas design for the fan ducting for the micro swiss direct drive conversion for the ender 3's and the CR-10s to allow use of the CR-Touch. https://www.thingiverse.com/thing:4933205 The reason I remixed this...

I'm going to remix SeeMeCNC's mount, located here: https://seemecnc.dozuki.com/Guide/RostockMAX+v3.2+Touch+Screen+KIT+Intallation+REV+B+MAY2018/105?lang=en. During the reassembly of my Rostock Max v3 after upgrading to the Rostock Max v3.2, I...

Mounted with four M3 Screws

Remixed from vegos thingMy 3d Touch has a smaller center-to-center distance

All-in-One Printer with Built-In Fan and Advanced BL Touch Technology

Adding a touch display makes lots of things possible that would otherwise require booting up a computer. The whole assembly is intended to be mounted on the outside of a printer enclosure. The hinge allows folding out the main body and adjusting its...

I needed a holder for my Brother P-Touch H100 to mount it to the wall or the side of a cabinet. As I didn't want to drill holes into the furniture I designed it with a hook that can be attached to the side of a cabinet - or as in my first case to the...

I needed a holder for my Brother P-Touch H100 to mount it to the wall or the side of a cabinet. As I didn't want to drill holes into the furniture I designed it with a hook that can be attached to the side of a cabinet - or as in my first case to the...

Ensure the screw is pushed all the way through the frame until you feel a tiny bit of firmness. Mount the BL Touch to the carriage with the 5mm screws. The screws will tap the plastic.</li> </ol> <p>5a. If you printed carriage and frames separately,...

This is the mounting bracket for creality sprite pro extruder. I needed it to adapt to my ender 6. ... Dimensions may not be perfect but it was good enough for mine.

This is a touchscreen mount designed for my Wanhao Duplicator I3 that utilizes an old Samsung Galaxy S3 as a touch screen interface for Repetier. The setup also serves as a webcam, leveraging the "IP webcam" app. Required printed components include:...

I specifically designed this bracket to securely attach a 3D Touch/BL Touch sensor to the standard auto-leveling position on my Geeetech A30 3D printer, ensuring seamless integration and optimal performance.