sprite cr touch mount 3d models

A remix of the 0 Y Sprite CR Touch mount to fit a V2. ...Ends up closer to 1 Y offset.

https://www.printables.com/model/255772-cr-touch-left-side-mount-for-ender-3s1s1-proI redesigned it for my Ender 3 S1 Pro.Reasons for remixThe original had its X-offset being-55.5mm however this didn't allow me enough room for my X-axis to reach for...

I also wanted it to sit in line with the Y-Axis of the printer nozzle.Offsets for the prove are X: 39 and Y: -1 (Z offset should be the same as the stock mount location)I'll link my Noctua 40x40 fan mounts as I finish them as well.UPDATE:...

If the two mounting holes are too small for the bolts, adjust the hole offset in your slicer so it prints the files appropriately (you can calibrate to find your needed offset by printing a tolerance test).No supports needed.Setup:You'll need to...

This is a [remix of BL touch mount for Sprite Pro extruder](https://www.thingiverse.com/thing:5555432). Credit goes to the original creator. Due to the size of CR touch, you might need to replace the bottom two socket cap screw with button head...

The original works nice for bl-touch, but does not enough room for cr touch wiring. So, i made a ugly, quick, hacky cut to fit my needs. ... Printed in ABS, 30% infill, on a modded Ender 3 gen 1.

It's recommended you do this first with just the screws (no CR-Touch or cable support) to make the threads, then take out the screws, and then attach everything to the backing plate. Remember to change your X, Y, and Z probe offsets. ...You'll need to...

Remixed tsuga's model to work on E3v2. ...Clearance for X endstop.Original model: https://www.printables.com/model/333070-cr-touch-zero-offset-probe-backplate-mount

But with a touch sensor like the CR touch, there needs to be an offset. Of the X and Y offsets, Y offset tends to create far more issues in i3 style printers and especially cheap printers that use V wheels (that’s why there are so many zero Y-offset...

Also, the runout sensor seemed a bit too low and would make contact with part of the sprite.I added the cutout for the connector.I extended the CR Touch's mounting point out a couple of mm to avoid the sprite's bolts.I extended the runout sensor's...

Just added a hole to the creator's design (https://www.printables.com/model/255772-cr-touch-left-side-mount-for-ender-3s1s1-pro) to be able to access the tensioner screw, not really need to touch it until you start to have extrusion problems like I...

This is an adapter to get your CR touch on your Ender-3. You should print this part with supports. You will need 2 extra screws; you probably can find some in your spare parts. The screws will make their own threads. Have fun printing! ... Video-...

This adapter pulls the CR touch closer to the X gantry and raises it up by 3mm. I needed this modification on the Ender 3v2 in order for it to be able to level (tram) correctly. ... The default position causes the sensor to be completely out of the...

this is a remix for the problem im facing in my ender 3 pro with sprite and crtouvh not leveling the whole bed for some reason

cr touch mount

CR-Touch remix

Same mount as original just added a cutout for the cr touch plug

Same mount as original just added a cutout for the cr touch plug

I like the Micro Swiss dual fan kit, but the author didn't have the CR Touch mount, only BL Touch which is different. So I drew my own. ...

I remixed this awesome mount for the BL touch to accommodate a CR touch, and still front mount it to the H2. You will need the following to install this mount:4 x M3x8mm screws2x M3 NutsMy Probe offsets are:X = 28.25Y= 27.60Z = 0.57

I couldn't find a proper mount for the CR Touch when I printed out the Blokhead, so I just put in a little cut out for all of the wires to slide through.

Update 1; I found that when I printed the original model I indented the wrong side of the mount for the CR touch and that the indentation was also too big, I have edited this and made the indentation smaller and on the correct side, I have printed...

A simple and quick-to-print BL Touch mount for the Creality Sprite extruder (pro). In addition to the BL Touch, you will need 4 X 10 mm M3 screws and 2 nuts. With this design, the BL Touch is mounted almost in the original location, which means you...

This adapter adds an additional 12.8mm to the x offset of the Sprite CR-Touch mount point (which makes my offsets roughly -44mm on the X and -41 on the Y), but allows a BL Touch/3d Touch to be mounted without the the retracted probe pin being at the...

This was measured and recreated off of the stock Ender 3/ / Ender 3 Pro CR Touch mount. I'm uploading this so people can use it as a reference point for making custom holders / integrating it into extruder mods. Drop a like if this helped you! ...

This is a Sprite Extruder/Pro shroud that will fit on an Ender 3 v2 using the existing hotend mount, will not work with the breakout board is the mounting holes is where the board would normally be  I have manual spliced and soldered the...

I hated all of the stronger designs having only one mounting hole for the crtouch (it pivots causing the mount to move too often) and hated how weak the spider mount was, which has two mounting holes. Well, turns out when the two are blended it...

This is a CRTouch Mount for Voxelab Aquila 3D Printer. ... Printer: Aquila Fillament: PLA+ 1.75mm Holes for CRTouch mounting are M3 0.6

... printer head upgrade. ...The design features a new CRtouch mount, since the original was for BLtouch. ...All the .stl files for the full upgrade: ( https://www.thingiverse.com/thing:4794720 ), ( https://www.youtube.com/watch?v=EQJfDLENYnU&t=238s )

Smooth Fang CR Touch Mount