spring auto rewind cable reel 3d models

Designed to be used with this mount: https://www.thingiverse.com/thing:3627169/files for the auto-rewind system: https://www.thingiverse.com/thing:3338467/remixes I now have the best of both worlds... swivel spool and auto-rewind! ... Thank you to both...

Once the wire is wound on the reel, you simply pull on both ends at the same time to retract the cable as far as you need and press the handle down into one of four holes in the reel to lock the reel in place while the cord is in use. Once you are...

Once the wire is wound on the reel, simply pull on both ends at the same time to retract the cable as far as you need and press the handle down into one of four holes in the reel to lock the reel in place while the cord is in use. Once you're...

Once the wire is wound on the reel, you simply pull on both ends at the same time to retract the cable as far as you need and press the handle down into one of four holes in the reel to lock the reel in place while the cord is in use. Once you are...

I based this idea off of the little auto-rewinders that they use on headphones and earbuds, only I scaled it up to a more industrial size. This utilizes the recoil spring out of a Troybilt TB22 trimmer I had laying around the shop. According to...

... the stand for zip ties to secure the badge reel in place. I redesigned the Dial to fit the new design. You'll need a bearing, Name Badge Reel, zip tie and all other parts from the Universal Auto-Rewind Spool Holder. ... https://youtu.be/gIy4VY0LTBA

I drilled a couple holes in the stand for zip ties to secure the badge reel in place. -I redesigned the Dial to accommodate the design. You will need a bearing, Name Badge Reel, zip tie and of course all the other parts from the Universal Auto-Rewind...

I drilled a couple holes in the stand for zip ties to secure the badge reel in place. -I redesigned the Dial to accommodate the design. You will need a bearing, Name Badge Reel, zip tie and of course all the other parts from the Universal Auto-Rewind...

... one point, a filament got yanked out of the MMU due to the autorewind function kicking in near its maximum force threshold. ...To mitigate this issue, I reduced the spring tension by removing two coils and replacing them with a shock-absorbing buffer.

Made this remix due to the original springs, did not last long, as well as it caused problems that the spring could not keep the filament tight due to the "short" return. Two different springs have been made, one running right and one running left....

A single film roll can be used per group of Neumade rewind reels.

Spring for Universal Auto-Rewind Spool Holder https://www.thingiverse.com/thing:3338467 modified to work with round rod.

Side wall mount for auto-rewind spool holder. Spot for needle nose pliers or knipex. ...

You can use those of any of the other spring-based spool holders such as the Parametric or Universal Auto-Rewind Spool Holder. ... Narrow: max spool width 55 mm, hub width 60 mmStandard: max spool width 70 mm, hub width 75 mmWide: max spool width 90 mm,...

I'm Excited to Share This Modified Spring for a Universal Auto-Rewind Spool Holder! https://www.thingiverse.com/thing:3338467 has been modified to accommodate Round Rods, making it an even more versatile and useful tool for DIY enthusiasts and...

- Chamfered tabs for easier spring stack assembly - Reduced hub wall thickness - Adjusted spring parameters to make it slightly more flexible V5.4 Oct 9, 2019 - Different decal characters top/bottom possible - Enable/disable decal character mirroring...

Cable Reel

Auto-rewind spool holders for MMU2. Additional parts needed per spool holder: 2x 608Z(Z) bearings6x M3 x 12 countersunk screws1x M6 x 6 pneumatic fittings

Update Dec 1, 2018: Alternative design available: [Parametric Auto-Rewind Spool Holder](https://www.thingiverse.com/thing:3252111) Filament load/unload issues? MMU2 taking up too much space? Not with this Auto-Rewind spool holder! It keeps filament...

* V1.11 (Jan 13, 2019): Added parameters for aligning the stop block with the universal auto-rewinder stand's grooves. * V1.10 (Jan 7, 2019): Fixed a dimensioning error and disabled bearing features when the bearing width is set to zero. * V1.09...

It appears that the text is a changelog for a Thingiverse project, specifically an auto-rewind spool holder. The changelog lists various updates and changes made to the design over time, including improvements to the spring system, axle, clutch,...

This is a complete package for an auto-rewind assy for the Sunly Filament Dryer. All components are directly printable and do not require further tweaking. The dimensions are optimized to fit a spool of 69mm (i.e. a prusament roll). Coupling rods...

So I added the following:Support for Integrated Auto-Rewind spool holder by VincentGroenhuis https://www.thingiverse.com/thing:3781815 as first done by rpgweb...

Multi-material GCode is available here: [link] Single-material GCode is available here: [link] Other gravity-based rewinders and community mods include: Circular Gravity-based Auto-Rewind Spool Holder Linear Gravity-based Auto-Rewind Spool Holder...

Cable reel for Gantry cranes

Cable reel for Gantry cranes

[~$8 on Amazon] Printed: One set of Vincent G's Auto-rewinder parts, minus the axle, and minus the stand, One set of these parts Other, not necessarily required: Silicone to seal things Glue M3 nuts and screws Flat-head countersunk screws...