spool roller 3d models

Here's a breakdown of the necessary parts and tools: **Parts:** * 1x [Rubbermaid 21-Cup Dry Food Container](https://amzn.to/2DSqK3n) * 4x [100 Pack 608-2RS Skateboard Bearing, Rolling Bearings, 8x22x7mm 608rs Bearing](https://amzn.to/2VwdkSu) * 2x...

- CAN V1 Totally Unmatched Superiority Holder - Container Version 1 Fits spools up to 75mm thick & 210mm wide in diameter Provides precise temperature, humidity, and weight readings in grams. Leds: Red indicates 0-250g remaining Yellow signals...

2 pieced per roller, they dont need to be stuck together or anything, you just simply print 8 of the roller pieces, and 2 of the holders, they weight and the angles loosely hold the rollers pressing themself together in the holder, each side can spin...

My spool holder is way too much to the left on my printer and the holder just doesn't work for spools with holes at and above 70mm. Therefore I tried out Tinkercad. Maybe it's too much filament but I just wanted to raise the spool a bit and make it...

Locate the spool cores exactly above the printer to minimize strain on the framework. ...Eliminate the need for a filament guide altogether, placing it directly at the top.

https://www.thingiverse.com/thing:3789524 JDs_Work designed this filament spool holder because they didn't like the way the original spool holder does not hold the spool centred on the axis of rotation (and neither did I). The holder is compatible...

I developed a BIGGER, light, more robust and running better version starting from my previous one I experienced a spool fall with the previous smaller one so I developed this perfect for 1 Kg spool thi is my V2 version with only one pin (Bottom)...

Filament spool holder for Prusa i3 MK2 and MK3 The support was desing in 2 pieces to be able to adjust to different spool width. Can be printed without support. It is designed to fit 608 bearings (8mm inner and 22mm outer diameter). ...*** Requires 4...

-------------------------------------------------------------------------------------------------- Filament spool holder for Prusa i3 MK2 and MK3 The support was desing in 2 pieces to be able to adjust to different spool width. Can be printed...

Parts needed: 8x 608zz Bearings: https://zaribo.com/rods-bearings/441-set-of-608zz-abec-9-bearing-for-filament-spool-holder-608.html 12x M3x14mm Socket Cap Screws:...

This thing is a remix of Wanhao i3 Duplicator Spool Holder by cyul. I have no M5 screws to spare, but plenty of M4 and M3 are readily available. The M5 holes have been adjusted for M4 nuts and screws instead. A copy of the original Tinkercad design...

Optimized side parts that can be screwed so there's no glue needed.

Customized version of http://www.thingiverse.com/thing:334558 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=334558 Instructions Using the following options:...

<p>I printed the original leg support, way too large to fit inside the dryer. ...I remixed so it will fit inside the Sunlu filament dryer.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>MakerBot</p> <p class="detail-setting...

This product is designed specifically for use with 10x26x8mm bearings. ...To ensure a snug fit, insert an air-tight foam seal into the inner recess area of the housing.

Print with p1s strength profile

Customized version of http://www.thingiverse.com/thing:334558 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=334558 Instructions Using the following options:...

Designed from a custom template found at http://www.thingiverse.com/thing:97807, Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=97807 Using the options specified: A bearing width of 7 millimeters A bushing wall...

Just remixed for the available bearing 6000RS: d - 10mm D - 26mm h - 8mm

This adaptation reduces the widening slot from 2 cm to 1.2 cm, allowing it to slip snugly over the edge of a server rack in a data center enclosure.

<p>This Part is meshed up from a Project of Daniel Crosslink</p><p>I have reduced the rack a little from material and made it</p><p>Made it compatible for smaller printers.</p><p>Corresponsding to this Video:</p><p>&nbsp;</p><figure...

needed a little more strength to where the slide mount is. ... added a large flat surface.

I'm going to move my printers out of my guest bathroom and onto one of the shelves in my mudroom that I recently purchased. Now I'm stuck with not much shelf depth, so I need to make the most of the width available. To accommodate the printers, UPS,...

just 2 Bic pens & 4 bearings (608)no supports needed !

Customized version of https://www.thingiverse.com/thing:25058 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=25058

You don't need any washers, just use the bearing as is, since everything is spaced perfectly. If you have a smaller machine, print the left side and right side separately. This design uses standard 608 skate bearings, which are easy to find. To get a...

I can not fulfill this request. Customized version of http://www.thingiverse.com/thing:321854 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=321854 Instructions Using...

Customized Version of Thingiverse Design 307228 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=307228 Instructions Using the Following Options: Washer Diameter: Set to 11.5 Axle Distance: Set to...

I printed the original leg support, way too large to fit inside the dryer. ... I remixed so it will fit inside the Sunlu filament dryer.