spool holder ultimaker 3d models

A straightforward replacement spoolholder is crafted for Ultimaker printers, accommodating spools with diameters ranging from 25mm to 57mm. This innovative design substitutes the original spoolholder located at the back. Inspired by a Thingiverse...

Spool Holder for Ultimaker Printers. To build it, you will need: - An eight-millimeter diameter threaded rod that is one hundred fifty millimeters long - this length accommodates M8 nuts. ...- Three M8 nuts - Two 608zz bearings - Two BearingHolder_PaL...

Spool holder for Ultimaker type printer. ...Designed for a rear wall thickness of 4 mm.

I fabricated these extra spool holders, only to discover they couldn't accommodate Taulman3D's sturdy Nylon Bridge spools due to their oversized diameter. I subsequently designed and 3D printed this spool holder using a resilient PLA material. ...Though...

Print Settings: Printer Brand: Ultimaker Printer: Ultimaker 2 Supports: Yes Resolution: .2mm Infill: 100% Notes: I used Alloy 910 Nylon from Taulman 3-D to print this holder. I experimented with Ply/PHA from Color Fab, but the tabs broke easily. To...

These cones float around the holder shaft without resting on it, held in place by the bearing's thrust face in both horizontal and vertical directions. This design eliminates the need for a shaft-mounted bearing, reducing friction. Manual adjustment...

This is a compact spool holder for use with 38mm wide spools that can be as long as 85mm in width. It's designed specifically for Ultimaker 2 printers. Get creative! To get started, simply place the spool upright on the two clips provided and make...

... the 3D printer's spool usage easily. ...To address this issue, we designed a spool holder for our Ultimaker 2, mounted at its side. ...We printed the required parts - a large flat hook and a cylinder with flute on top - without any support structures.

This consists of three parts: (2x) Folding arms, ums5-spool-holder-normal.stl (2x) 3D printed pins, printer-spool-pin.stl (1x) axle, either print pipe-with-holes.stl, or cut an 8.5" length of 1/2" PVC pipe and drill two 1/4" holes through it (see...

Rear wall support system for Ultimaker printers specifically engineered to withstand a 4mm thickness challenge.

Used for Ultimaker S3 for 1kg spool. ...

Spool holder for UliMaker 3, S5 and S7.Supports one 750g spool plus one 2.2Kg Spool.Fits perfectly on the printer with the original NFC sensor and bottom part.Prints in two parts, with 4 alignment pins.

The standard Innofil/Ultimaker spools do not fit this modified holder, but replacing them is just as effortless as swapping out the original spools. ... I started by utilizing the original file provided in the acknowledgement section (Roland Benner)...

The Innofil/Ultimaker spools do not fit this holder, but swapping them out is as simple as the original. I retrieved the original file from Youmagine.com, designed by Roland Benner, and modified it to suit my needs by adding a thin base and an end...

This spool holder will hold a spool with a body up to 76mm. The Innofil/Ultimaker spools do not fit this holder, but it is as easy as the original to swap out. I took the original file frombhttps://www.youmagine.com/designs/spool-holder-xl (Roland...

The Innofil/Ultimaker spools do not fit this holder, but it is just as easy to swap them out. I accessed the original file from the link in the acknowledgement section (Roland Benner) and modified it to suit my needs by adding a thin base and an end...

Small modifications were made to the excellent low friction spool holder for the Ultimaker 2. Recently, another filament supplier was used that utilized 9cm wide spools which wouldn't fit. To accommodate this, a longer core was created (with a length...

... heavy spool loads. ...PLA is not recommended as it lacks the necessary "spring". ABS or PET materials, such as Colorfabb XT, are preferred alternatives. Additionally, the Spool Holder fixture and Filament Guide fixture require support during printing.

Operating a Ultimaker 2 with Unconventional Filament When utilizing uncommon filament with a narrower diameter than usual on the roll, specific adjustments are required. Ensure your system is calibrated for these unique circumstances to guarantee...

My DIY Spinning Holder for UM2 Pro, designed for hassle-free printing without unnecessary supports.

Manually crafted for bigger coils - reaching a maximum of 105mm in width. ... This encompasses the 2.3kg and 2.6kg coils utilized by numerous manufacturers, boasting widths ranging from 100 to 102mm.

People use this human for coils that have a tiny opening, yet they're also capable of holding larger ones quite comfortably.

... holder cover V1.0" sits on top. To align the "Wave V1.1", it rotates freely. Then button head screw 2x M3x20mm tighten. Now, the Spool holder can be mounted to the Ultimaker. ...With grub screw DIN 915 M3 x 6, ease of adjustment is now available.

A heavy-duty spool holder for Ultimaker Original is designed with optimized print direction to enhance joint resistance. By assembling it using ball bearings, rolling resistance for heavy spools can be minimized. ...For assembly, you'll need one M8...

I created a straightforward Filament spool holder for an Ultimaker today. It conveniently fits into the existing spool holder slots. ...Despite being non-solid, it boasts impressive strength.

The original UM spool holder failed to accommodate RS-online spools, prompting me to create a custom design that integrates seamlessly with the existing holes on the back of the Ultimaker and securely holds RS PLA spools. ...These spools measure 7.5cm...

Benefits over the stock holder: - Easier to load filament - Can handle 1kg spools - Easy to see how much material is left - You don't have to pull you printer out every time you have to change filament - Fits all Ultimakers ( unless the ledge is...

This holder is designed for spools up to 83 mm wide and with a hole diameter of up to 50 mm. Its main advantage lies in that the plastic spool sits as close as possible to the back wall of the printer. ...Suitable for spools: Fdplast (1 kg), ABS maker...

It's handy when space constraints prevent accommodating two spools on the original holder. My own HB configuration required this adaptation to support dual extrusion. The setup relies heavily on an available PSU. 1. ...Print settings: three shell...

Very simple spool holder for Ultimaker S3. Probably wouldn't work with other printers/models as there is a strict clearance 4 mm between the back edge of the frame and the printing head. So, it must fit precisely. But I am including FreeCad source...