spool for cable 3d models

Reel for winding 5 meter fiberglass rope. Diameter is 195 mm, height is 20 mm. ...

The outer diameter of the center axis is 23mm for all spools. Sides are secured to the axis using a M20x2.5 thread whose tolerances have been tweaked to be more FDM-friendly. Furthermore all spools and axis have openings through to the hollow center...

*Tips are appreciated and go towards creating new designs* --- CHANGELOG: * 2021-10-30: * Added experimental male-male axis connector for use with an (experimental) separator for creating multi-spools * 2022-05-07: * Added a winding aid. Use an M6...

You'll need two per spool.The axis should be printed upright and may need a 3-5mm brim, depending on how good your adhesion is.For stability reasons I'd recomment at least 3 shells and 10% infill, for the axis I'd say use 5 shells and thus print it...

I designed a custom cable spool to fit my needs after searching for alternatives that were sturdy enough for mobile use, had practical designs, and could be printed in one piece without support. Most other options I found were too flimsy or...

Use this small spool / reel for cable management around your 2020 extrusion. Good for USB cables. Has openings for threading a connector or for zip ties. M4 screw holes. ...No support required, at least with PLA on my CR-10.

Spool to hold cables. ...Good for headphones and charging cables. ...Printed in soft TPU so that the other lips clamp on and hold the cables.

This are some Cable Spools, for USB and other computer cables, i created to be lightweight, in print time and stable enough for transport. I designed them to be able to print in Vase Mode and at least with this printer here they fit perfectly...

Spool to wind wire with grooves and a centre pocket to hold headphones or connectors. ...Useful for headphones or charging cables

Carefully place the device over the cable connection, then fold it into a compact shape for easy transportation. When you're ready to deploy the sound system, simply unroll it and get set up for music enjoyment. ...The design files are stored in Pro/E...

The spool has a notch in it that lets the inside end of the cable come out through the center of the spool, while the free end wraps around the spool. It's designed for this $8 network cable: http://smile.amazon.com/gp/product/B0057XC49K Print...

The spool features a notch that allows the internal end of the cable to protrude from its center while the loose end wraps around it.\nIt's engineered for this $8 network cable: http://smile.amazon.com/gp/product/B0057XC49K\nPrint...

This file is designed specifically for customizing Bottom of the spool.\nUse this file to make changes and updates.\nTo see the complete thing, visit http://www.thingiverse.com/thing:1398088\nDon't forget to customize the bottom too, found...

... project, visit http://www.thingiverse.com/thing:1398088. Customizing the bottom part is also crucial; you can find that file at http://www.thingiverse.com/thing:1405596. Be sure to use the same specifications for both inner and outer diameters.

This is another cable wedge for extension cords and your average filament spools. I had trouble getting the the other ones to fit and not crack, so this is simplified and a bit more robust. Just print two of the these and drill a hole into your...

Wall mount for cable reel holders up to a reel diameter of 9 cm. A lot of material, I know, but the reels are very stable and easy to remove. I do not like the holders where the reels hang on a rod and you have to sort so much, rebuild and...

I've been working on a reliable cable spool design for quite some time now. After numerous attempts, trial runs, and mistakes like broken spools and tangled cables, I'm happy to share this latest iteration with you. This design is specifically...

I had 10 different wires, therefore i designed the the Cable_rail for 5 wires. ... With washers between the spools you can assemble up to 10 wires (see the picture).

My solution: Create a spool that would allow the user to pull out as much cable as they need while maintaining tension on the spool. Tension is maintained by having the cable feed through a small hole in the rim of the outer Spool Half. The two...

A Simple Wall-Mounted Cable Spool Holder for the Ultimate Organized Workspace. I recently rigged up a sturdy cable/filament spool holder on my wall using double-sided tape to secure it in place. To connect these holders, I opted for a 40mm PVC pipe,...

This is a variation of a cable spool for SRAM road bike shifters. It is like the original SRAM cable spool, but is a little bit smaller in diameter to pull less cable, therefore move the derailleur a bit less. The spacing between cogs on a Shimano...

Spool holder for the "CLASSIC" wall shelf system produced by "Element System". The mounts are tested. The spool holders are for hanging in small spools and are also tested and are working fine. The tape spool is not tested and most likely too big...

For the "CLASSIC" wall shelf system by "Element System", a spool holder is available that has been thoroughly examined. The mounts are designed for small hanging spools and have also passed testing. ...However, a large tape spool remains untested as it...

The holes in the original did not line up with the holes in my spool holder so I moved them a bit to fit the one's marked in red in the photo which are suitable for the same diameter and pitch screws as the original one that needs to be removed,...

Customized version of http://www.thingiverse.com/thing:1405596 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1405596 Instructions Using the following options: $fn is set to 100 Wall thickness is set to 2 Inner...

Cable organizer for this spools: https://www.pollin.de/p/schaltlitze-liyv-0-25-mm2-560048 I bougt several colors with 0,25mm^2 and 0,14mm^2. There are slots for M3 Nuts to attach it to the wood parts. The rod is made of 14mm round beech (Buche)....

Due to the ground up redesign though, this is not a direct remix of those designs. If you want to check out a wall mounted version of this, check this thing out: https://www.thingiverse.com/thing:4202518 This 2nd version includes a cable reel which...

The "slider" should not be glued.\r\n\r\nAll parts were printed with 3 walls and 15% gyroid infill.\r\n\r\nThese are just what I used so as always, use your best judgement on what works for your printer, and good luck!\r\n\r\nParts are not oriented...

The spool holder is designed specifically for use with an M8 rod, while the knob rotator accommodates an M8 nut, providing seamless integration with your existing setup. This design is tailored to work seamlessly with popular spool holders like...

... the platform without one. You have to carefully take out the inner plate from the MK2 spool holder, install the cable guide, then re-install the plate securely. ...In this case, securing the cable guide nicely proved to be a clever move after all!