spongebob with muscles 3d models

Customized version of http://www.thingiverse.com/thing:46884 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=46884 Using the following options: qr_scale = 1.7 obj = 4 qr_thickness = 5 perimeter = -1000 tag_width =...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

The human brain contains an estimated 86 billion neurons, each with thousands of synapses, which are the connections between neurons that allow them to communicate. This vast network enables us to process information, solve problems, and navigate...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

The design allows the physical joystick to be in the same location as the stick in the game and to not interfere with using the MFD’s and control panels. Rubber bands tension the joystick in pitch, roll, and yaw axis. Clamps to your desk for easy...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

The built in support has been added in a way which will come off easily with minimum efforts. ...Start sliding in the GoPro mount base in the slots as shown!</p><figure class="image"><img...

Here is a filament tractor bench that I built for testing purposes of polystruder XR3 filament extruder.&nbsp;You will need following electronic parts to built.Stepper controller with built-in driver:...

Fill the tube and partially fill the syringes with water. Try to keep the air bubbles to a minimum. Push to small syringe to zero. Put the large syringe in the pump. Back up the pump just enough to allow the syringe to fit. Start the calibration ...

This part could potentially be laser cut from acrylic, or another sufficiently rigid 3mm material that can withstand the nearby heat of the (insulated) heated bed plate.Assembly stepsDisassembly of the Super Racer and assembly of the new frame,...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

That version of the case requires no additional hardware; the lid will just press on and depending on printer precision, hold with friction. Post-Printing The case Bottom has built-in support on the extrusion clip. Carefully remove this support...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

After a few tests with varioshore, I found the ideal parameters. Maximum foaming and gyroide filling around 10% (to be adapted according to the weight of your handle).The Blender file is supplied if you wish to adapt it to your needs.6 -...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Attach the top part of the outer shell (CaseTop.stl) with 4 M3 screws. * ADJUST THE OUTPUT OF THE BUCK CONVERTERS BEFORE PLUGGING THE RASPBERRY PIS TO THEM. * Wire the electronics * Power your system. You might want to power each card one at...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror...

The half version come with flat face that can lay on the printing bed easily. However, if you want to reduce the amount of "staircase" artifacts on the surface, you can print it in upward position, but will result in longer printing time and plenty...

I hope you really like my idea and will share it with your friends. If you use this method, please tag me so I can proudly see your results :) HINT: Downloading the .zip file does not work for some reason. Just download file by file. ...

Customized version of http://www.thingiverse.com/thing:368375 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: ...

2: New Hegstler with a more accurate appearance. (“eagle_plate” should, if possible, be resin printed). 3: Higher clearance between pvc tube and printed parts (21mm). 4: New Trigger group: Trigger now has a coil and the Selector has 3 diferent...

Using the following options, a customized version of http://www.thingiverse.com/thing:287025 has been created with Customizer! (http://www.thingiverse.com/apps/customizer/run?thing_id=287025) Pixel size is set to 0.7, Panel shape as 1, Border width...

The small amount of testing I have done indicates that the device can create several 1000's of ppm O3 from room air in a few minutes inside a sealed 1 gallon ziplock bag (filling the bag with medical oxygen before running would produce much higher...