spongebob squarepants sponge holder 3d models

2022 Update: fixed most annoying bug on the design - holder for gear that holds planet. It used to not support the gear properly resulting in gear jamming under sun gear. Now it should be fixed. Update comes in two parts: updated part and add on. It...

 Print file includes:24cm LED strip (8mm) holders with end adapter, venting, 3 screw holes, and lens interfaceLight Mount connectors (connects light mount strips together)Wire Rack interface hooksOptional end cap for cleaner lookPrintable lens...

This is a remix of Max Kern's great ZeroBot robot (more on Hackaday.io), with the following changes:HeadlightsGrooved tiresCharging portFront panel holder.Also, thank you Kelly Jordan for the inspiration with your aggressive tank tread.Some extra...

Battery slides into the holder at the front of the vehicle as shown on the pictures below. I use rubber band to kip it from moving or falling out when the car flips over.PCB installationThis step is done last, after everything else is assembled. Main...

There are also holes in the top for integrated cup/pen holders with a 3D-printed translucent sleeve and light strip channel so they light up too :-D I used birch butcher block. I tried some dark stains, but I found that the light birch did not take...

Tested in onward. This is a rifle/controller holder I created to play various shooter games on my quest 1 & quest 2. This is a remix from another version that had closed handles. For quicker movement, I opted to cut the controller handle's sides...

The spindle holder is designed for a 52mm diameter Chinese mini lathe (cheaply available at hardware stores and tool shops). Both nema 17 and nema 23 motors can be used. As a control I use an Arduino uno with its CNC shield and 4 Pololu drivers....

If you're using the stock everything on the X axis, you can orient the Y carriage plate as it was previously.Using the new M5 bolts, mount the belt holder to the bottom of the carriage plate. Pay attention to the belt alignment, which loops to the...

Then just put 3D printed motor gear on motor shaft and attach the whole motor assembly to the motor holder in uicm-stator part with two small zip ties. After that, just put in two uicm-rotor parts so the gears link with motor gear and fix them with 4...

TL;DR first: Welcome to my Overhaul of the Creality Ender 2! Im starting here with version V2 (V1 is only in one picture; there was too much wrong with that), which comes in 2 iterations/stages: ++++++++ Stage 1: ++++++++ changing out the Heatbed to...

The lid uses the colour change method again***You can just do it two / three coloured or go all out and change for every resource colour (a huge pain to do!)The PlayerBox.3mf has both box parts with supports Game Piece HolderThe 2 d6, the thief, the...

... Updated item description. Updated screen mount STLs. Added source files. Added slicing suggetions.  4/11/2019 Redesigned PSU mount to work with bed wheels. 3/27/2019 Added missing STL file for PSU holder. ...Renamed PSU files to be accurate.

IntroductionA simple pair of magnetic holders for attaching flat bellows to a metal lathe as ways covering. I used this 5/8" tall flat bellows available from McMaster Carr:https://www.mcmaster.com/1320K111/These bellows are made for this job and are...

Make sure they understand you want a ring and the star, or you might get a negative (I sent the green picture along to make it clear - the DXF only contains lines, so it's hard to tell). Added mounting holes: I used two old leather belts to make...

Rotate parts so that surfaces vital for concentricity (such as bearing holders and pivot block posts) face upward. The only part that is tricky to print is the stick surround. Split this part in half when printing and use high detail. The stick...

The center handle locks in and keeps the lid closed, avoiding putting any stress on the hinge to do so.UpdatesUpdated my model to keep the same spacing but different grip sizing so that different pens/pencils can be accommodated for four and five pen...

With a filling in the order of 20% they occupied me 1.4 - 1.7 kg of PLA +.The spindle holder is designed for a 52mm diameter Chinese mini lathe (cheaply available at hardware stores and tool shops).Both nema 17 and nema 23 motors can be used.As a...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

Print the light bar and 3 of the nut holders. (Steps 1 & 2 from the non-switched version) 3. Clip the ends of the mini rocker switch so they fit inside the enclosure once it is inserted. 4. Loosely place the LED strip and switch where they will go...

If you have access to a 3D printer, it would be best to pre-print some of the parts in the download, in particular the BLTouch holder and extender plinths. The BLTouch v3.1 probe (raised using M280 P0 S10 in GCode terminal) will need to be set at...

That was one of the first mods I did, right after the rear spool holder. My printer is getting old now and the carriage that the cartridge slides into is getting kind of worn and sloppy. It just doesn’t hold the cartridge nice n tight like it used...

 Fiddly little cables, bend ratio >10.Wall thickness of 1.6mm (0.4mm extrusion) or 1.8mm.   Ethernet5Pretty typical, you probably want to increase the bend ratio to 8x   Laptop AC7.5This is a rough average based...

The second axis is controlled by the belt in case of simple motor setup - No hyperstaticity thanks to the clearance : one of the bearings is free and the other is fixed by the screws to adjust parallelism and allows a small degree of freedom of ball...

I used a smooth/wipeable melamine faced furniture board) 580mm x 450mm x 18mm, QTY 1A Spool of PETG ,QTY 1Some PLA ,QTY 1EiBotBoard, QTY 19V 1.5A AC/DC Power Supply Adapter 5.5mm x 2.1mmPen Holder, QTY 1Precision Hardened Steel Smooth Rods - 8mm,...

I tested it out and it seems good, but to stop the weight of the cables plugged into the dock pulling it back I used some Command Strips on the bottom of the dock holder to keep it in place. Bill of MaterialsRequired: 3D printer and filament (inb4...

Bend the rocker switch pins so they don't touch the first battery For those who have already printed the first version https://www.thingiverse.com/thing:5418531 only print parts 11,12,13,14,15 to upgrade to V2...

IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE...

The 4 larger holes on the very top of the main case body are for heat-set inserts; the 4 larger holes on the face of the main case body, where the PSU holder mates with it, are for heat-set inserts; and the 4 larger holes on the lid that the fan...

- https://www.printables.com/model/855331-megalopolis-dice-tower-with-a-story Electronics:Voltage Sensor Box - https://www.printables.com/model/784371-voltage-sensor-box Voltage Sensor Box - SMALL...

It can hang off the plywood deck (¾ inch") or the slightly thinner shelving above. Support enforcers are neededNo gluingEasy to printDesigned on...