spongebob pen holder modified for printing 3d models

Quick holder for your pens to attach to the fridge. ... Fits 3 x 10mm diameter magnets inside (no glue required)

if you like this pen look at my profile i have several you can print in 3d or cut with a laser good luck and enjoy the impression

The spool holder is not high enough for some filament spools where the center opening is extra large which causes the spool to hang lower and sit on the top of the printer rather than hang from the spool holder. This spool holder is about 10mm wider...

I modified the original vat holder to accommodate the Anycubic Photon Mono X. ... Fit's nicely and does what it was designed to do.

The hinge piece has been modified to bring the holder about 2mm further out from the mounting clip (the back edge of the lid would otherwise scrape on the holder in my case). Also, I deleted the built-in support fins on this piece, which were...

I'm glad to offer a remixed version of the External Spool holder for the FlashForge Finder 3D Printer by CreativeTools. This revised version lets you securely attach the spool holder directly to the side of your machine. It's designed to print in...

Here's a handy pen holder designed specifically to cradle your KaWeCo sport pens. ...Enjoy!

I fine-tuned the modified model, adapting Berslan's design by swapping out 8mm x 3mm magnets readily available at Home Depot for something new. Additionally, I upgraded the bearing to a 16mm x 5mm x 5mm unit that happened to be lying around, just...

Modified the Board Holder STL file to add a small slot on the side that secures the Micro SD Card Reader module. ...&nbsp;Allows the reader to slip in and fit snugly.</p>

This is a remixed 13mm holder for the Planetary Gearbox Motor Visualizer by LazyMaker to fit MK3S+ extruders with the Delta P fan duct.The bottom right leg has been shortened to eliminate interference with the fan duct.Print at 99% scale. ...I have only...

This is a remix of SpongeBob sponge holder by _Fatguy with drain holes at the bottom so it can be sticked on a wall with double side tape. ... https://www.thingiverse.com/thing:5225957

I didn't design this USB cable holder, but after taking a closer look, I really fell for its design. Rounded corners are especially appealing on items permanently mounted, as they significantly reduce the risk of accidents - and we've had our fair...

There are two versions available: a simple one with vertical rails, and another with rails plus a mount for an 18mm proximity sensor, as well as the ability to tighten the mount using a screw. The source file has been included in this remix;...

Modified middle part of http://www.thingiverse.com/thing:780379 project to make it possible to adjust mounted fans vertically. Two versions: simple version with vertical rails rails + mount for 18mm proximity sensor + ability to use screw for...

... using the existing screws. Then, slide in the camera base. The rest of the components are taken directly from the original files. I'm using a Microsoft Lifecam 3000 and paired it with the tripod holder from https://www.thingiverse.com/thing:2235879

Small modifications were made to the excellent low friction spool holder for the Ultimaker 2. Recently, another filament supplier was used that utilized 9cm wide spools which wouldn't fit. To accommodate this, a longer core was created (with a length...

Spongebob and Squidward houses for aquarium fishes. Print the model with multiple filament colors. ! Be careful, choose a material that will be suitable for animals. The material MUST NOT contain toxic substances and similar dangerous goods. ! stl...

... groove that securely grips onto my bike seat clamp, preventing it from sliding down. To print this modified design, I utilized supports in Cura, which intelligently avoided placing them in the zip tie grooves, ensuring a smooth printing process.

I printed this spool holder, but found that while the base sat nicely on the top rail, every time the extruder pulled filament, the whole thing fell over because there was no way to really secure it to the printer. I used TinkerCAD to extend the...

The "length" of the spool holder can also be adjusted, which might be necessary for spools with a smaller radius. I have included an STL file for 40mm spools, slightly shortened to fit a small printer's build volume. ...I left the feet unchanged from...

Designed to fit affordable E27 standard lamp holder from Leroy Merlin (https://leroymerlin.ru/product/patron-plastikovyy-e27-dlya-podvesnyh-svetilnikov-cvet-belyy-13637940/). To assemble, simply secure plastic nuts together and feed the cord into a...

Hypercube Revolutionizes Evolution: The XY Stepper LR Holder Upgrade Brings Unmatched Stability

I've customized the lamp holder to accommodate three 5 millimeter LEDs.

I tailored this template holder: http://www.thingiverse.com/thing:1412866 and merged it with a large-sized half bin: http://www.thingiverse.com/thing:1363711

... noise and vibration, consider adding a decoupler. However, doing so may cause the motor to press against the original holder, resulting in contact. ...This modification eliminates this issue by incorporating a thinner back plane behind the motor.

I swiftly updated the locking cone so that I could print this face-down without any supports, resulting in a perfectly smooth first layer. ...A huge thank you goes out to the brilliant creator behind this fantastic project for their outstanding work!

... with the frame to mount my Caddx Ant Lite w/ connectors. ...This modification lengthens the mount, so that you can grip around the connectors. In addition, the LiPo holder has been made slightly thicker to hopefully form a stronger grip on the battery.

Utilizing The Following Options: Spool Diameter: 57 Bearing Diameter: 19 Printed Settings: * Three border layers for optimal stability and durability. * Layer height of 0.2 mm ensures precise, intricate details. ...* Ten percent infill density provides...

... however, old stock is available. The outer diameter fits correctly in the pen changer. The inner diameter is being fine-tuned. Printed with a thing-o-matic in ABS, overhang issues were resolved by adding paper tape to the pen above the holder.

I came across TheRavenMaker's concept for mounting a dial (http://www.thingiverse.com/thing:1260597) and actually built it, but then decided to make some modifications. My printer is a dual extruder, but I removed one of the extruders to reduce...