spinning top toy 3d models

On G-Code tab, simply set the "Build volume" parameters with the proper build volume HINTS ON TFT FW: --------------------------- * Sometimes, after a TFT FW installation, the FW can need a reset / recalibration in order to properly boot up, as...

These are my filament changes if you wish to slice your own: DHD (top):Single color gray print.    DHD (trunk):Start with BlackChange at 2.15 to GrayChange at 17.0 to Red    The DHD top should just press...

It is mainly just a personal preference of which surface finish you want on the top (vertical print lines or textured surface).MINI Light Bar Spare HW: Slightly modified version made to be able to use hardware that comes with the Prusa kits. Uses...

The blade with the teeth goes on the bottom of the stack, and the blade with the flat-sided hole goes at the top of the stack.Axle: The flat surface of the axle has the word "SPRING" printed on it, to indicate the side that your spring goes. Slide...

This pack contains over 3,000 Christmas decoration STLs generated from the top 3000 first names in the USA. The pack also includes PNG renders of each Christmas decoration. The decoration is 60mm in diameter. For long names the width may be wider.

Das Video des 3D-Drucks ### Zusammenbau der Flatfieldbox Doppelseitiges Klebeband und Posterstrips anbringen. Am besten leicht überlappend. ...

Pay attention to the DSI ribbon cable.Add the M2.5 20mm hexagonal spacer (14) on top of the Raspberry Pi 4.Wire the 12x12x6mm tactile button (24) and prepare to mount it to the Case B:a. Screw first the M2.5 4mm screw (15) in Case C<br/>b. Then mount...

Installation: Very simple, just slide the top of the remote into the bottom of the wrap. Please note that is it a very tight fix, and a good amount of strength is needed to move it in place. On the other hand, you don’t want to use excessive force,...

The input and output rods are trapped structures with a 45-degree angled top that allows bridging over them without an unsupported span. The OR logic is very easy to implement by having a pusher block that spans the (two or more) input rods such that...

(Das von mir konstruierte Blatt beinhaltet zusätzlich auch eine M2 Schraube mit entsprechender M2 Mutter.) Ebenfalls solltest du doppelseitiges Klebeband im Sortiment haben um das gelbe Gesicht auf den Helm zu kleben sowie Leim, mit welchem du einige...

http://www.thingiverse.com/apps/customizer/run?thing_id=243650 Instructions Using the following options: box_shape = 0 box_top_height = 10 box_height = 20 custom_shape =...

To do this only connect one of the colored wires going into the driver and combine the two colored wires from the lamp to the one colored wire on the lamp.The high level process is:Check the length of the COB Led against the mount and cut it where...

The top cover with the 20mm hole you can enlarge with sandpaper and a round stick or a file. When the radial fan is removed, you have a look onto the crosshairlike shape to brake down the airflow - I removed it. Put in the old fan and you can see...

## Modifying the model If you want to change the size of the model, this can easily be achieved by changing the attributes at the top of the openSCAD code. All of the measurements are unitless, but mm should be used as those are the units used to...

I have found it's best to close without saving, and reopen the file (Setting every parameter should take a minute or two, tops.. which is why I've built it that way).What if you REALLY break it?If you do completely break the model and accidentally...

I have already seen a couple of things that I'd like to change, like putting the rudder hinge in the same side as the servo and mounting the aileron servos on the top of the wing instead underneath it (i don't know if I'll change that one) Of course...

The 5v + needs to go on the second pin from the left on the top of the small chip in the bottom right of the board.  Here's the screen all wired for 5v...

We also reduced the fill from 22% to 10% to help reduce the weight as well as thin the walls and top and bottom (The OpenRocket report shows the performance based on the original print, not the updated print). We knew we wanted a display stand that...

If you opt for a larger frame like I did, the T8 lead screws might be slightly smaller and won't reach the top corner brackets where the 608zz bearings are inserted. To avoid reprinting, I just hot glued the 608zz on the underside of the hole. I have...

We took into account your wishes, and most of the clothes and textures are compatible with each other (including top and bottom clothing compatibility) without clipping and other typical problems (see demo video and screenshots). It was a challenging...

On top of the Y carriage is a mounting plate for the laser driver, as well as a connector board for easier disassembly. Note to self: next time don't use closed chain belts. And buy multi-wire cables...</p> <h4>Electronics</h4><p>The electronics has...

Even despite the fact that I did this test with the first version of the new duct which was not anywhere as good as the latest version, the result shows almost no deformations and it has a near-flat top surface. (Note: you won't be able to get this...

Now the new switch only needs to be attached to the X-axis at the top right. To do this, loosen the screw, ideally put an Allen key through it from the other side so that the roll holder does not fall apart, attach the switch and screw everything...

| | marklin-front-hull.stl | Front and top arrow-shaped hull, integrating nacelle pylons, and forward deflector. | | marklin-rear-hull.stl | Rear hull including impulse unit. ...

Then, the spring structure is “pinched” on the top to make a cone-shaped spring. Next, the contour of the spring body projected onto the sketch. Finally, a sweep function is performed to create a flat spring. It’s easier said than done as Fusion 360...

The two-5015 fan small-distributor doesn't blow enough air and the box tops out at around 45C. The heater I chose has a built-in thermostat which shuts it off if the heater temperature gets too high, and with the small distributor the heater...

First is a cross section for the middle parts and a fill up version for bottom, top and sides. The last element is a little corner plate to fit the overall new look. The elements are 90mm in height, so they are recessed about 10mm below the...

If you want to see them organized, check this out on [Prusa Printers](https://www.prusaprinters.org/prints/78695-mega-lego-like-skeleton-101-scale/files).* If you're print using the 3MF files (recommended), you will need to print: (All supports are...

The bracket itself is mounted via two bolt hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the light fixture can be removed from the brackets by...

&nbsp;If you load the corresponding Prusa Slicer project file, you can proceed and slice the model directly, but if you load the STL files directly, you need also to create an infill modifier loading the infill STL piece that will be used for...