spinner 360 camera 3d models

I may provide STLs for other stanchion diameters and/or strap widths upon request, but I would encourage you to modify the design from the provided Fusion 360 file if needed and share the results here.Edit 1-30-22: I have added STLs for a 22mm...

The model was created using Autodesk Fusion 360, and is fully parameteric - with a caveat: the model is so complex that when one changes the early parameters (like the diameter of the lamp socket), one has to fix some artifacts (like drilling the...

9,5cm diameter 8,7cm high printed in 14 pieces (base, top, 6 bars, 6 panels) no need of glueing (but it's safer to hold it by the bars when moving, especially when tealight or candle is inside) you can additionally lock the bars with a thread (tie...

Step 1: Use a 3D modelling program (i used Fusion 360) Step 2: Create a solid layer which is as thick as your first layer (0.2mm for example) This first layer will be the layer which touches the print bed. I used a glass bed for almost perfect...

GRBL Mega 5X 1.1l axis A on E0 socket Set stepper driver trimpot at 0.5V (1000mA) $1=100 step idle delay (very important) $103=180.00 steps/mm $113=3000.00 max rate $123=300.00 acceleration $133=360 max travel (degrees) (blue wire on 2B pin) 30°...

I could be persuaded into a 360 video and a beat saber expert plus with or without comparison tho. Q: Why are you doing an FAQ with yourself? A: I prefer the interview format. Q: Does this work with "XYZ headset"? A: No but heres the link to...

... I use Fusion 360 to design the model. While trying to maintain a supportless design I tried many different options but I still end up with the dovetail design. I do not want to use any external fasteners so this limits the design options further.

All parts were rebuilt from scratch in Fusion 360. Apologies in advance if any of the items below are included in another remix I have not spotted. In this remix I have: 1.Created a sturdy 3 point fix solution for the base to the mounting plate...

-  While plenty of quality 360 circular coling solutions are already published for anycubic printers, none of them have room for bltouch probe or require switching to...

Video can be found here: https://youtu.be/d8us3OWgS1A Editable Fusion 360 source files can be found here:https://www.cgtrader.com/3d-print-models/hobby-diy/robotics/3d-printable-high-torque-servo-gearbox-version-2 This servo/gearbox is the new and...

It was designed from scratch in Fusion 360. It includes a built in battery box for the coin cells.</p> <p>youtube video:<br/> <figure class="media"> <oembed url="https://youtu.be/hNSt9VCsHqQ"></oembed> </figure> </p> <p>The parts you'll need other...

When I was a little blue at being unable to figure the damn thing out, I turned to 3D design and began by making a 360 degree quick little arrow dial based on that standard diagram that all the textbooks have. You can use it to figure out the mean...

Note: - I can email the CAD files which were created in Fusion 360 if you want to make adjustments. Be aware that since this was an interactive design the files are pretty messy. - If I have stepped on anyones toes with this design, just let...

Included the Fusion 360 file for modification. It fits both my XPS 13 9370 and my work Latitude 7390, although the XPS 13 is a bit thinner so it wobbles around a bit more than the Latitude. The dock side itself could be a bit smaller for a tighter...

This replacement, courtesy of John O'Shaughnessy, pushes out the endstop just slightly to clear the mount. Fusion 360 files available Part of the Emma Puggle Railcore II Collection | Description | Link | | --- | --- | | Railcore II BMG + Precision...

What's new is that this one is modeled with the great Sverchok add-on for Blender, which allows non-destructive, parametric modeling with curves and surfaces in Blender. This could be done much easier in a proper CAD software such as Onshape, Fusion...

&nbsp;I am including the Fusion 360 export for those who wish to close up my fan hole and create their own. &nbsp;You should add feet to the bottom to hold it up off the ground as there are vent holes below the PI slots.</p><p>I tried to keep it...

... I ended up building mounts with some scrap wood, gluing them to the underside of the table, and sliding the control box into it. Edit: I'm going to be re-making these parts in Fusion 360 and adding a part to reinforce the legs of the lower table.

You are now ready to begin aligning the X rails.\r\n\r\n[Full Fusion 360 file available here](https://a360.co/2Ag3s5Y).\r\n\r\n----\r\n\r\nChangelog:\r\n* 2020-06-07: Initial release\r\n* 2021-01-30: Uploaded Halo Magnum Top Cap variants. ...These are...

At the rear, it features two drum-type fuel tanks.After assembly, the turret rotates at 360 degrees and the gun can be lifted at 45 degrees. The caterpillars have been modeled and optimized to be 3D printed in resin and are movable. All manholes can...

These pins can be made out of short pieces of regular 1.75mm filament, regular paper clips, or you can print the 1.75mm cylinders that come with STL files;- Hydraulic cables that connect the model's parts can be printed (they come already twisted in...

I have exported Fusion 360 .F3D files for each component, so you can edit sketches and modify things to your own design. Hardware Required: 6 x M4 30mm Hex Stand-Offs 4 x M4 20mm Hex Stand-Offs 12 x M4 40mm Button Head Hex Screws 14 x M4 12mm...

The model was designed in Autodesk Fusion 360 and has been adapted to support 3D printing. The model consists of 16 staves, 2 chime hoops, 2 bilge hoops and 2 sets of heads (3 parts each) so it can be assembled as either a bank or a jar. All the...

The maximum usable print area is now X=360, Y=320, Z=300. However, the practical print area may be smaller. I have redesigned the center carriage with only one extruder to gain extra print area. Any J head, E3D V6 or similar extruder will fit and...

... Once more detectors come online in the next years we should get new signals with much better determined inclination. Modelling The slices (between 150 and 500 for each model) were assembled into a 3D model in Fusion 360 using a python script.

(48 Inches total) (order two https://www.amazon.com/gp/product/B01I49ESN8/ref=as_li_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=B01I49ESN8&linkCode=as2&tag=geardownforwh-20&linkId=15a7d465440f2b17cefa18475533843f ) and you'll be set\r\n - For the...

In Fusion 360, for some reason, threads aren't "modeled" by default. So you put them there, they look pretty, but when you export the STL, there are no threads. It's like Schrödinger's cat - the cat is alive, the cat is dead. You just can't tell...

Zorvath has three eyes on top of his head that let him see with 360-degree vision. He has very steady hands that make him a trusted worker among many people in Speedville. Not only does Zorvath fix cars, he also loves to drive hot rods in the...

Thanks to Product Design online for his excellent tutorial for converting mesh to solids in Fusion 360 https://www.youtube.com/watch?v=pgWWVcM5YJY \r\n\r\nFinally, an LED tea light to light it up at night. I have a large (2 inch diameter) tea light...

This helped me get my head around a few things in Fusion 360, and is a little cathartic at times. Here's what I've got: **Note this list will change shortly** * Beer_Tokens_Tray_v2.3 Holds 6 sets of beer tokens, along with medal Print 4 times *...