spektrum 6ch 3d models

Adjust frequencies on the receiver instead.

This model was created using Tinkercad. ...You can modify it right now by visiting https://www.tinkercad.com/things/cY1wVlOZrMm.

I grew tired of my radio constantly falling over whenever I tried to lay it down, so I decided to take action. To keep this from happening again, I created a simple solution that attaches directly where the old handle used to be and secures with two...

Spectrum IX 20 Tray

<p>*** If you like the file please make your “ like ”. &nbsp;Every mark helps me to get a free roll out of Prusa. &nbsp;Thanks…. ***</p><p>Printed with regular PLA. No rafts, bridges or supports. ...&nbsp; I use it on my DX6 &amp; NX6.</p>

I'm installing a new wall mount that's significantly slimmer than my previous design, mainly because the DX9 Transmitter handle has a notably narrower profile. ...The print job turned out perfectly after printing upright with a 0.3 layer thickness.

Using this in a project to add a DeWALT battery to my remote so I don't need to use screws to remove this cover. I probably should use this to create a sliding door as well, more people would want that I imagine. ... Category: R/C Vehicles

Just a wall hanger to keep things organized. ...Print in PLA without supports.

TPU material is incredibly flexible and has been rigorously tested to withstand even the most severe crashes without sustaining damage.

A small hiding spot for style... ... Enjoy!

I want to use my DX6i as a student transmitter (buddy box). But I'm not thrilled with the bulky original antenna. So I completely disassembled the stock antenna. I replaced it with an IPex 2.4GHz 150mm antenna from eBay, which only cost around 4...

This steering wheel is specifically crafted to match perfectly with the DX4 and DX5 series controllers.

Für den Tyro 89 , zur verwendung eines SRXL2 Recievers und gleichzeitiger Aufnahme des AKKUS. ... Gedruckt mit Raft auf einem Ender3

I designed a custom enclosure for my Specktrum AR7700 receiver that features an open port for PPM as well as a holder for a PTFE tube to elevate the antenna vertically. This setup offers protection for the receiver, allows for effortless antenna...

The custom brackets I created don't fit the DX7 TX properly, so I designed new brackets with a smaller grip area instead.\nPrint Settings\nRafts:\nNo rafts will be used in this print.\nSupports:\nNo supports are required for this...

Just take off your old fan cover and screw this one on. It has a very tight grid son only dust can get into the fan which is not bad for it at all. ...You need to do high resolution because the holes are so small(1 mm) and a raft.

Monitor Spectrums Inductively Held By Humans

Use a cable tie to reinforce the antennas. It's remarkably slender and light in weight. ...Perhaps too slender?

This is a new receiver box for the sr315, sr215 and sr515. ...This receiver box is meant to be held together by electric tape to keep the box as small as possible.

The Antenna Positioner Safeguards the Elements and Complements 1X2.5Mm Cable Tie Use

Adding a DeWALT battery to your remote control is a great way to simplify the process of accessing your device's interior without needing to remove screws from the cover. This project can be a fantastic opportunity to enhance functionality and user...

Your Flight Experience Enhanced by Spectrum Radio Integration System.

I needed to mount something off the back of my DX8 transmitter so modeled this in 123Design. ... May need some filing on centre clip for a good snap fit.

I crafted a custom attachment for my trusty DX8 transmitter, designing it specifically using the powerful tools available in 123Design. ...Now, I'm eager to assemble it, but first, I'll probably need to make some adjustments by filing down the center...

Using this in a project to add a DeWALT battery to my remote so I don't need to use screws to remove this cover. ... I probably should use this to create a sliding door as well, more people would want that I imagine.

We need some safeguards in place to shield the recipient from harm.

A mount for the SPM4650 receiver to make it easier to attach to a model and constrain the antennas safely. ...The antenna tubes are meant to be glued into the slots.

I wanted to free up some room on my shelves so I built a wall mount specifically for the DX6i. ...Two number eight countersink screws fit perfectly into place, securing everything tightly.

I wanted to free up some shelf space, so I came up with a custom wall mount for my DX6e. ...Two number 8 countersink screws fit together like a charm.

Time had come to build a mount for the wall, so more shelf space could be created. ...A design was printed out, and it functioned flawlessly as expected.