speedy wing 3d models

Friends of flying planks, rejoice! ...I've crafted a unique wing that bridges the gap between the Speedy Red Mini Wing and the Red Duck. ...This specially designed model boasts a wingspan of 1000 mm, while its total weight checks in at a mere 870 grams.

For all fans of flying planks, I created a version with a size between the Speedy Red Mini Wing and the Red Duck but utilized a distinct airfoil. This design boasts a wingspan of 1000 mm and weighs 870 grams. Like the Mini Wing, the wing features two...

For all friends of flying planks, I've designed a special version that falls somewhere between the Speedy Red Mini Wing and the Red Duck. This design features a unique airfoil and comes with a wingspan of 1000 mm and a total weight of 870 grams. This...

Uwe Heuer - experienced flying wing designer and Horton specialist - says about this square form of a flying wing, which he loves to call "panel plane": They do have a low damping and flight stability around the pitch axis (elevator), therefore you...

Connectors 4 mm carbon tube The holes for the connections are only parallel: In the middle, between the wing_center and the two wing_middle_rigth/left (50 mm in each side of wing_middle, 200 mm total at front tubes) (60 mm in each side of...

Instructions All sections of the wing are only held together by two slightly elastic plastic cords inside the tubes They are fixed with luster terminals on the wing ends There are only short joints to connect the parts Connectors 4 mm carbon tube The...

They are fixed with luster terminals on the wing ends.\nThere are only short joints to connect the parts.\n\nConnectors 4 mm carbon tube\nThe holes for the connections are only parallel:\n\nIn the middle, between the wing_center and the two...

This is a cutting-edge forward swept wing designed to integrate seamlessly with the fuselage of the "Speedy Red Midi Wing." The carbon rods run continuously through, delivering exceptional stability. To assemble this wing, you'll need one 8mm tube...

This is a forward swept wing that can be used with the fuselage of the "Speedy Red Midi Wing". The carbon rods pass all the way through, providing exceptional stability. You'll need one 8 mm tube and one 5mm tube, each 1000mm long. These rods are so...

This is a forward swept wing you can use with the fuselage of the "Speedy Red Midi Wing". The carbon rods pass all the way through, providing extraordinary stability. You need one 8 mm tube and one 5mm tube, each 1000mm long. These rods are so stiff...

Additional Parts for Thing 1117576 on Thingiverse I Designed This Because I Refused to Use Gummi Rings to Secure the Wing Not Yet Tested, But Ready to Go!

Mounting Plate for the Speedy Bee F405 Wing Makes It Easier to remove FC by only gluing down Base Plate to Aircraft

This is the massive version of the Speedy Red Swept Wing. It boasts a wingspan of 1510 mm and weighs in at 1250 grams. Just like its smaller counterpart, this big wing has sections held together by two internal strings within tubes, secured with...

This is the Large Version of the Speedy Red Swept Wing. It now has a wingspan of 1510 mm and weighs 1250 grams. Like the small wing, all sections are held together by only two cords inside the tubes. They're fixed with luster terminals on the wing...

This is the large version of the Speedy Red Swept Wing, boasting an impressive wingspan of 1510 mm and weighing in at 1250 grams. Like its smaller counterpart, all sections of this big wing are held together by just two cords inside the tubes,...

The performance is shown when one flies it speedily." Uwe Heuer - experienced flying wing designer and Horton specialist - says about this square form of a flying wing, which he loves to call "panel plane": "They do have a low damping and flight...

Here are the specifications for this extraordinary bird: Specifications: Airfoil: Clark YS Wing span: 794 mm Chord length: 160 mm Center of pressure: 27 mm Overall weight of wings: 270 g Surface area: 12.7 dm² Empty fuselage weight: 75 g Fuselage...

This servo mount is tailored specifically for Wersy's smaller swept wing aircraft, providing a precise fit for the Powerup Micro servo weighing in at just 9 grams. ...The Powerup Micro servo itself boasts dimensions that are notably taller and wider...

... and the original design, the slot for the servo arm has been adjusted accordingly. HB: When installed, the cover can be lifted 0.5 mm from the wing's bottom surface due to the different servo size, however, it does not impact flight performance.

Flight is stabilized by two servos cleverly concealed within the wings, which utilize a wing-mixer program stored in your transmitter. Update 1 (10/09/2017): A sleek new canopy features two precisely drilled 3mm holes, allowing for the secure...

Update: Winglets have been designed and can be attached to both wings using standard slicing parameters. Three loops and 25% infill settings produced optimal results. While winglets fit snugly into their respective positions, it is recommended they...

A Flying wing with a wingspan about 616mm, and a weight less than 300g with electronics included Update 1 (10/09/2017) : New canopy with 3mm-holes, you can put a 3mm-wood-beam into it to fix the canopy with some rubber bands. Look at picture to see...

The sailplane features a high-speed wing profile (Eppler E184) that enables fast ridge soaring performance. Update 1 (10/09/2017): A new canopy design has been added, complete with two holes for a 3mm wood beam. This allows the canopy to be secured...

After discussing it with the author of Speedy "Red Mini Wing," I created a universal insert based on the original part with their permission. I imported the original part into OpenSCAD and removed all walls from it. Then, I added four corners to...

This addon is specifically designed for use with the 3D printed Canopy from http://www.thingiverse.com/thing:1117576. I created this accessory because I encountered difficulties removing the Canopy, which features magnets to secure its position. ...To...

A printable remote-controlled airplane with a wingspan measuring approximately 616mm and weighing around 300g, including electronics. The aircraft was crafted using Blender 2.78, while KISSlicer version 1.6 was employed for the 3D printing slicing...

Um den Empfänger einfach und mittig über dem Flightcontroller zu platzieren, habe ich die Halteeinrichtung erweitert. Es passen sicher weitere ELRS-Receiver mit bis zu 20x15mm² hinein. ############################## In order to place the...

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=1074909 Instructions Using the following options: line_1 = Spooky line_2 = Speedy line_3 = Sprint stoneScale = 5 fontSize_3 = 8 fontSize_2 = 10 fontSize_1 = 6 build_plate_selector = 4