speed square holder 3d models

If you're inspired to use them as drawer organizers, toy train tunnels, a super fat pen holder or whatever, go for it. I'd love to see any makes or remixes from my design so please share them. ...I'd also like to hear any suggestions or ideas for...

German Version below: UPDATE 18.10.2021: Made a full and thicker ring, so the spool won`t get stuck anymore on the filament holder as it was in my case! For this just make sure the holes you make in the old spool are exactly on the other side! With...

Adjust the mirror test stand until the return beam hits below the green LED on the slide holder. Exact positioning shown in the photo. Reinsert the slides with either the knife edge or Ronchi covering the green LED. For Foucault testing, the razor...

Finally, make 4mm thread on each side of them using M3 die with die holder, remember to apply thread cutting oil before cutting thread.Watch videos below to see how thread cutting and assembling the wheel can be done. Social Links Facebook:...

also includes a Frame parts with 2 neutrik panel mounts incase you would prefer the usb connection location here, and use the center chamber part as a location for the pcb.Please notice, for the lamp holder connectors on the buttons, you may have to...

More information about this function: https://www.youtube.com/watch?v=u4YONDL4iXo (Chep) When you have some experience with it, you can print more boxes at the same run if your bed is big enough. If you made it this far, Happy Boxing :) More...

This set generally depends on the closed box to keep everything from mixing around. Most pieces are custom designed with the exception of the card holders (and the MakerBot Pocket T-Rex skull): Cards - 60 count - base - ICT Cards - 60 count - lid -...

The friction of the threaded interface, should be greater than the friction of the bottom of the knob against the side of the stand.IMPORTANT, this is THE PART to the functionality of the spool holder. It can be tightened to produce a little friction...

It can also be taken out of the holder for ease of putting new plastic on it. 06.02.2022 Added print instructions and plastic usage. Happy to find out that this whole project only uses 437g of plastic. Also added Ender 3 controller board mount. It is...

Make sure to push the tube until it stopsSlide your Original Prusa Filament spool holder (or compatible model) to as far left as possible on the top rail of the printer. You should find it aligns very well with the mount point on the Z-Axis cap.Mount...

The stl files have the name, *UpdateUxcell RF-500TB-Holder *UpdateSmallGearUxcell RF-500TB-ShaftLinker *SmallGearGeneratorShaftLinkerPerfectFit (There was an error in the diameter of the hole for the motor 31ZY shaft fit) It is fixed. NEW GEARS RANGE...

This was my first hurdle and I attacked this by moving the bottom seat of the rod holders in towards the center by 6mm on each side. To help the smaller “left” gantry I added some small extensions that wouldn't interfere.</p><p>&nbsp;</p><p>I tried...

The rotor of gyroscope made by Sphero. Print instructionsLicence: Creative Commons - Attribution Category: Engineering How I Designed This This gyroscope consists of three circles as gimbal and holder. These circles can by printed in one piece. Each...

*Supports Everywhere* * Ryobi Adapter * Ridgid Adapter *Supports from build plate* * Ryobi Latch (both) *No Supports* * Ridgid Battery Adapter * Ridgid Battery Adapter Lid * Ryobi Contact Holder (make sure to orient this properly on the build plate)...

I've been using the holder for over two months and it hasn't bent in any way ... finally! I hope you enjoy sharing and that it can solve your problems as it solved mine, now I can fully appreciate the Hemera! BLTouch Offset setting { X, Y, Z } ...

The hardest part is getting the X axis end holder off. I used a hammer and a heat gun and a punch, but this looks like it would have been a lot easier. https://www.thingiverse.com/thing:2738089 Your X axis case can be tossed in the garbage after...

Power switch:https://www.pollin.de/p/einbau-druckschalter-pbs-12a-420206 Fuse holder: https://www.pollin.de/p/sicherungshalter-s1066-260442 Clamps for speaker cables: https://www.pollin.de/p/lautsprecher-anschlussterminal-640060 Check out my other...

UPDATE: As requested, I uploaded additional parts necessary to create the red (column) version of the clock, minus the holders for the quarters at the ends of the seesaw pendulum, which I cannot locate. To assemble this version, you'll require all...

Headlights and Tail Lights: These are basically place holders. You can print them and put some LEDs in them for good lighting, or you could leave the covers off and fill the area with epoxy to encapsulate any LEDs you put in there too. Head/Face:...

The “flip-out” part was my attempt to mimic certain drill bit cases where the bit holder is movable. It might have been overkill for 5 keys but I would probably lose them otherwise. The case would be consider a “snap shut/open...

I know there are buffers with separate units for each filament, but I wanted to keep it clean and in one box. As you can see, it is a box with chambers separated with printed dividers and this box have a click system with 5 slots for filaments. Print...

... for every tip or donation, it means great recognition for me and helps a lot to keep going! My some other things: 3D Printer • Accessories Electronics Tools • Accessories <img src="http://like-it.link/things/Rotating-PCB-Holder.jpg" alt="Rotatin

It would probably also work with the Mod-S version.For easy switching use the MMU2 PTFE holder PC4-M10 mod. This is what enables quick switching from one RMU to another by just switching the set of RMU output to MMU tubes and running through the...

The use of a special variable makes it much easier to use existing complex geometries as place holders when positioning other objects. $show is chosen over $visible as I find the variable is used frequently enough to require shortening the length of...

I had already printed the original construction, but had to realize that the holder / stand is not stable enough in strong winds. For this reason I designed a stand that also serves as a mount for a generator. I use a Nema stepper motor as a...

I widened holes to use the Anet A8 X Belt holder and tensionner by Miranina (cuz I like it): https://www.thingiverse.com/thing:2425783 This is made just like the original for E3D V6 and V6Lite, and Clones. I suggest you test assemble everything to...

If you print cleanly, the imitated terminal block fits perfectly into the bottom of the shuttle - alternatively you have to file it down a bit.First the angle was fixed to the wall, then the white base frame was pushed on, the black support on top...

The first row is connected to the Ardiuno pins, the +5v in the next position and GND on the last. I'm using four (4) 1.2v rechargeable AA batteries in a 2x2 snap-in holder for power. Wired directly to the 5v rail of the Arduino. I had previously...

... <font size="+1">^Like</font> button** and turn that heart red <img src="https://cdn.thingiverse.com/site/assets/like-button-liked.svg">.                                                                 

Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work. Our puzzles are modeled using the open-source...