soru soru no mi 3d models

It connects to the wire rack shelves I use to set my amps on (shelving from Home Depot).A support enforcer is needed.No gluingEasy to printDesigned on...

3D-Drucker Düse Nozzle 0.4mm für E3D Hot Ends V5, V6 (0,4mm)...

No supports needed, assuming your printer is capable of a decent amount of bridging.Use M3x8mm screws to mount the TFT to the holder, and the holder to the lid, and the clamp that holds the DC connector in place. Use M3 screws of an appropriate...

An ivory coloured "natural" colour PLA or ABS (I used ABS) is ideal.I recommend a 0.10 layer height or less to get maximum grey-scale resolution.You need to print the images solid with no air gaps. Set many top and bottom layers and 100% infill to...

Assembly should locate onto original hotend bosses, but no hardware is used here. Use 2x M3 x 10 Button/Socket head bolt to secure the top ears to the captured M3 hex nuts in the mounting bracket. Use 2x M3 x 10 Taper head bolts to secure...

I bear no responsibility for any harm or damage caused by making or using this robot. This robot is dangerous. Do not proceed to make it unless you fully undertand the danger and are of sufficient skill to avoid harm to yourself or others.</p> <hr/>...

No glue is required for the assembly. There is a detailed video guide that will walk you through the assembly. Click the video icon at the far right of the model’s picture slider.After being 3D printed, the figurine will stand 208 mm wide, 190 mm...

The SLS version of Dreadnought was divided into 2 new scale versions of 1:72 and 1:96.One part of Lock (2_Ge_lock_7S_(x4)) you need to print 4 times.New sizes of this model:FFF/FDM 2.0 version 1:48 Scale dimensions:After being printed will stand -...

Theres no guarantee it will fit similar Bike pumps as I took measurements from the exact one I have. DISCLAIMER: By downloading these files, you agree that I shall not be liable for any damage, injury or harm resulting directly or indirectly from...

I had to rotate the powerbank maybe 30° to fit my usb cables, because the connerctors where protruding quite a bit)Step 6.3: Connect top and bottom, no screws needed. ...I glued the white middle part on one side and inserted copper rods (with matching...

Supports certainly won't hurtRHD Fan DuctMaterial: ASA, ABS, PC, or comparably heat-resistant filament&nbsp;Layer height: 0.15mm&nbsp;Infill: 20%Notes:The DesignI'm very much learning 3D design as I go, and with no prior experience. It's likely...

The SLS version of Vulcan Tank was divided into 2 new scale versions of 1:72 and 1:96.One part of Lock (2_Ge_lock_10H_(x78)) you need to print 78 times.New sizes of this model:FFF/FDM 2.0 version 1:48 Scale dimensions:After being printed will stand -...

If the clamp doesn't fit or is way too loose, your printer may need to be calibrated.&nbsp;There are no chamfers on the edges, because chamfers are a PITA in OpenSCAD. A work-around is to load your clamp 3MF/STL into <a...

No chance to fit the 20mm high fan into - so I designed the additional case in fusion360. This is to fit on the right side on the moving printhead. I decided to fit the prototype first with double sided tape. It works without the weight of its...

My finger and thumb got multiple very shallow slices in them before I even realised what was happening (so maybe wear a kitchen rubber glove to install or remove the caseless objective, lol).This objective has a nominal aperture of f/4, which is an...

---- Step 1 - Sawing Lamp "Glasses" From a Polycarbonate Twin-wall Sheet There is hardly anyone who will have a polycarbonate twin-wall sheet in stock at home, and no one is likely to buy a whole 1m x 2m sheet just for a few square centimeters. I...

Holster has no attachments, it uses Blackhawk Serpa adapters. Video (russian): https://youtu.be/oXulr7C7kEo ###Parts list 1. Main part - Main TM.stl or Main STTI.stl 2. Lock part - Lock TM.stl or Lock STTI.stl 3. Top cover part -...

Notes: When I say to discard a part that's no longer needed I mean stick it in the spare parts box not throw it in the bin. If any holes in the printed parts are a touch small, just run an appropriate size drill through them (bolts are all M3 or...

 Doing this will maintain the orientation of the door and tabs which is required for them to print correctly.  Other stuff:If you need some bins for small parts, the following bins with covers are a good option to use with the Box For Stuff 20 bin...

This is left to the maker to finalise, as sometimes folks may want or need to use differing materials for the scoop and the LED ring, which themselves have differing shrinkage rates upon cooling after printing.As it's still a large work in progress,...

Updates ======= 2021-10-07 Added a Flsun Dragon bowden connector - see Notes section at the end 2021-10-11 Added Volcano magnet spacer if reusing stock magnet holder 2021-10-11 I've now tested the design with the plate printed with ABS printing...

You can pay with PayPal or your credit card.Watch the tutorial video on how to assemble Isaac Clarke​ 3D Printing Figurine at Gambody YouTube channel.Also, you may like other Heroes 3D Printing Figurines._______FAQ: Where can I print a model if I...

Personally, I use LED lamps of no more than 3W in my constructions. Assembly Please also refer to the set of attached assembly photographs when reading these instructions. Shades Please note: Since some parts of the shades are quite thick,...

I dried them for two cycles on this print bed dryer, and then after 12 hours in the vacuum chamber, weighing them at each step.&nbsp; One cycle (2 hours) was not enough, but two cycles (4 hours) resulted in no additional moisture loss (by weighing)...

Accesorio para hacer una trenza ligera, trenza de pelo de moda, herramienta para trenzar, pinza de pelo con rizo mágico, para peinar bollos, para peinar, trenza, clip, moño No pierdas más tiempo intentando crear nuevos peinados. ¡Este accesorio hace...

Now you have the chance to create your own vapor polisher.Disclaimer:I take no responsibility for this of any kind! Acetone is dangerous for any organism or plants. Take care while working with it. It's also explosive and can produce significant...

On Fusion 360 there is no flat coil option, so we used the coil option to create a spring structure. Then, the spring structure is “pinched” on the top to make a cone-shaped spring. Next, the contour of the spring body projected onto the sketch. It’s...

Step 1 - Sawing Lamp "Glasses" From a Polycarbonate Twin-wall Sheet There is hardly anyone who will have a polycarbonate twin-wall sheet in stock at home, and no one is likely to buy a whole 1m x 2m sheet just for a few square centimeters. Perhaps...

Parts are created in 3d modeling software, no copyrighted product had been scanned in any way. These models are for personal use as proxies and should never be sold. ...If it causes copyright issues, i will remove it.</p> <p><a...

Supports touching the build plate (only) are suggested, in any case no supports are needed on the threads. 0.1mm resolution Post-Printing Putting it together First, make sure to clean the "elephant foot" from the parts and also clear any supports. I...