sonos roam mount 3d models

This is a very simple mount that holds the roam in place with light pressure from the prongs sticking up. It is intended to be stuck down to a surface using 3m double sided strips. ...But can easily be modified for screw holes.This initial design blocks...

... for the Sonos Roam Holes for the screws are 9mm countersunk head and 5mm holes for the thread. ... Charging wire is routed through the small gap before mounting the Sonos Roam mount to the wall. This will insure the cable stays in place. ...

A wall mount for the Sonos Roam Holes for the screws are 9mm countersunk head and 5mm holes for the thread.

Even though the Roam is made to … roam with sound, I need a place to store & use it as just another Sonos speaker in my setup. So here it is. When putting up the two mounts, make sure to place them on the inside of the rubber-thingies on the bottom....

A small extension to the original model to make it wall mountable with support for 3 screws. I tried command strips but the speaker was too heavy(and concentrated) so drilling works better. There is room for the power cable to be attached. ...Make sure...

A remix of BonkMonk's nice wall mount that adds enough cable space in back for the Roam's charging mount to fit in the holder. ...When installing it, have the charge plate running through the cable channel and hanging over the side so you can access the...

customized with 3D Slash!

The problem with just putting it into the bed: The off switch on the back is very easy to press and it happened a lot to us, that the Roam was accidentally turned off just by some movement.So I remixed this mount I found here and just added some...

I designed this wall mount for a Sonos Roam speaker. It allows the speaker to be positioned in the corner of a room, and higher up to improve the audio quality. Speaker faces out from corner at 45 degrees to ensure audio distributed evenly. Mount...

I've only printed the horizontal brackets so far - and one thing I notice now I have printed them is they will work either as a shelf you can put the Roam ON, or as an under shelf/desk mount that you can suspend the Roam from. This might be slightly...

I got the new Sonos roam and wanted a wall mount.So I designed a simple version so that it can be placed with the front facing towards the listener and with enough room behind the speaker for the charger cable.I hope you like it. ...PLA is strong enough...

This is dock for the new [Sonos...

Sonos has presented a portable speaker called Roam (https://www.sonos.com/en-us/shop/roam.html) , a dock is sold separately but it is also compatible with the Qi wireless charging standard. This designs aims to provide a printable dock that can...

With this handy thing you can hang your sonos roam on your shower rack while showering. ... I would love to see your prints of my design.

Have been using my IKEA Livboj wireless charger for my black SONOS Roam for quite some time... but today I felt like making it a bit more "nice"... I'm actually quite happy with how this turned out. Fits like a glove... and when printed with black /...

Have been using my IKEA Livboj wireless charger for my black SONOS Roam for quite some time... but today I felt like making it a bit more "nice"... I'm actually quite happy with how this turned out. Fits like a glove... and when printed with black /...

This is a speaker shelf for the Sonos Roam that only relies on the outlet for support. There are two parts that need to be printed and glued together, preferably with epoxy. Additionally, this stand ONLY works with a 10w Apple charging adapter. ...I...

This is a Sonos Roam holder that takes the place of the bottle holder (bottle cage) on your bicycle. It should fit standard bottle cages and use the M5 bolts that come with your bike, but I left some wiggle room for the bolt placement. It is...

This then allows the Apple MagSafe charger to align and attach to the case to charge the Sonos Roam. I have also redesigned the overhangs so supports are no longer needed.</p><p>The case has tabs and holes to attach rope or paracord that can then be...

This then allows the Apple MagSafe charger to align and attach to the case to charge the Sonos Roam. I have also redesigned the overhangs so supports are no longer needed. The case has tabs and holes to attach rope or paracord that can then be...

The case uses tabs with 4mm holes to attach paracord. Designed to be easily clipped to a backpack or hung around campsite. Access hole for USB-C port and power button on back. Used supports for front top overhang, the tabs to not need supports. I'm...

<p>The case uses tabs with 4mm holes to attach paracord. Designed to be easily clipped to a backpack or hung around campsite.</p> <p>Access hole for USB-C port and power button on back.</p> <p>Used supports for front top overhang, the tabs to not...

The case uses tabs with 4mm holes to attach paracord. Designed to be easily clipped to a backpack or hung around campsite. Access hole for USB-C port and power button on back. V1 used supports for front top overhang, the tabs to not need...

A swivel mount, adjustable and equipped with a locking mechanism, designed specifically for use with Contour Roam camcorders to facilitate easy angle changes while ensuring stability.

I fashioned a custom camera mount specifically for my Contour Roam, which I've fitted onto my trusty Triumph Street Triple. Although tailored to my bike, the design should adapt easily to most motorcycles. ...To accommodate the new setup, I replaced the...

The tabs of my elemnt roam broke, so i printed a new one to be glued on. first you have to remove all of the tabs to get the printed part on the wahoo. The holes are used to squeeze glue through. A SLS/SLA printer is adviced as a FFF printer is...

... the Inspiration and Those Amazing Models That Led Me To Take on This Challenge. Update: Just Mount It Straight Onto My Helmet - Now It Needs Some Major Refining to Account for the Bulge of the Camera, A Good Sanding Later Revealed a Decent Finish.

No one uses these old Contour cams anymore, but if you're a dinosaur like me and still do, this'll let you mount it to some pic rail. ...Only whipped up one side version, if you need something for the opposite side just mirror it or somethin' Three...

I really liked the look of the original stand, but it wasn't quite big enough for the charging pad I had. ... So I remixed it to make it fit a 100mm x 10mm charging pad.