sonoff sv case 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=46884 Options used: perimeter = -1000 qr_tolerance = 0.001 per_h = 10 per_w = 3 tag_height = 80 hole_r = 10 hole_y = 0 hole_x = 30 case_thickness = 2.4 obj = 0 tag_width = 80 corner_radius = 10...

  I do these as PLA on PETG supports as well set to SNUG:For more info on that bit, see the Prusa article on this at:https://help.prusa3d.com/article/combining-materials-xl_498103These are all printed with PETG, 0.2mm layer height and the supplied PS...

Of course, infill type and amount are not critical if printing the “gearwheel” type tire.Do not forget to use a glue stick or painter's tape as an underlay when printing TPU on a PEI base - otherwise it will stick “a little” too good to the...

You might have to talk louder to make the sound of your voice penetrate the filter and the deflector. Filter Material: Use the best filter material available for your purpose, and in emergency cases, filter materials that are suggested by authorized...

In any case, before screwing the assembly down, slide in the Förnuftig filter to ensure alignment of all parts. Then use wood screws with washers to fix the assembly to the shelf/bottom of LACK table at the 4 outer screw holes (be careful to not...

Dice-Tray-Standalone.stl is just the little slider bit from the dice tray, in case someone wants to print those out to use without the whole character tray solution. So, once you've got them all printed, how do you fit them in the box? You can see...

Much like with the smallest cog, a little extra cable pull is added insurance to make sure that cog is reached in case the cable pull was minutely too little over the previous ten cogs. Again, the limit screw should be set to prevent the chain from...

  It's certainly not enough time to take photos when you are working by yourself!Cut the top to the finished size you require - in my example it's 352 x 272 mm which is enough to give a few millimetres of overhang, in this case I like the angled...

In this case, please contact, it is possible to save files at high values, but this will give a sharp increase in file size. This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the...

I did a lot of work in fixing correct sizes for everything, but surely its not proven in all cases and every print setup may create its own displacements. For testing I designed Printer test presets that are simplest, least material consuming objects...

https://www.mictuning.com/u_file/1610/products/19/07a6902dde.jpgOptionalFuse holder and fuses - I'm not sure this was strictly necessary but I wanted to put a fuse between the hot terminal on the battery and the speed controller just in case...

As Christmas is nearing and as it's always a difficult task to find gifts for my parents and grandparents I thought lithophanes would be nice. But of course they need something to hold them and provide the backlight needed. So of course I went and...

STEP-File is included, just in case you need to adopt the mounting holes. Sometimes, the IR sensor doesn't recognize the flag depending on the material used. To overcome this issue, I've painted the top part with a black marker. Testing Did some...

The pack of files for this configuration is available in the scales: one in forty, one in forty eight and one in eighty.Parts:salyut7_front x 1salyut7_back x 1soyuz x 1progress x 1panel1 x 3panel2 x 4antenna1 x 1antenna2 x 1antenna3 x 2Big parts...

 I included printed versions though in case you cant get them.Aluminium Mesh - the sides have a mesh insert.  I used some from a car shop, normally used to back body work repairs for my original project.  I modeled some up but its the...

- dynamic flight consumption 21A - hover at 24.5 to 32% of throttle As conclusion, 4S battery with more capacity could give better flight time, the additionnal weight created can induce faster propeller's ans could make the flight more stable,...

PHOTOS In case any of the photos are not self explanatory, here's what they show: Installed auger, looking into the hopper. You can see that the screws protrude through the other side of the shaft. That's a good thing. We don't want more places...

The difference between the sizes, is the length of the modules (in case the rack being used is not very deep): Regular 147mm Short 108mm Extra (ex-) Short 91mm There is also a version of the Extra Short center box which does not have a vent for the...

Failing that, these are very easy to design, even in Tinkercad and its really only the "Guide" that will need to be changed. If you have something very close in size but too big, PLA will easily soften if you warm the metal part up and push it...

Some coaches however were equipped with gas lighting systems using coal gas where available and in some cases acetylene gas where coal gas was not available. The print itselfI was kinda inspired by Sam's trains to make my own printable rolling stock....

Just in case this does not get updated please check the thing files themselves for available options.Installation1.I have also uploaded some basic installation guides for both the stock & the V6 versions. The guides only cover the basics to get...

In my case, there is an overheat issue with the extrusion stepper (it's hotter than other stock steppers), I think the new stepper has lower voltage than the stock one, I will add a buck converter to fix that. But it's not a design issue anyways. It...

It is currently identical to the regular M2 except that the servo cases are plastic. Battery access is through the battery hatch, which also carries the skids. Note that the stock battery will probably not fit. The preferred battery is the...

The D-Taps are primarily there to allow for larger more power hungry camera systems however the 12v supply from the POE splitter can only deliver 30W max which in most cases will be useless as it must power all of the head and the camera system. The...

Use a piece of cardboard to support the PCB on top of the printer to avoid shorts.Remove the motor wires from the JST connector and put some heat shrink tubing on the motor's individual metal connectors.Make a chart like this (in this case let's...

Congrats! Step 16Now print the second fan housing for the left fan, in case you want to. I do not explain how to assemble it, since this is exactly the same - only simpler ;) The only thing to mention is, that there's hole to get the fan cable...

In the fusion file there are the sketches of the two designs, in case you want to do it the same on both sides. It's just that I'm very strange, one day I want to make minimalist designs inspired by Dieter Rams and the next day I'm very baroque and...

In this case, I recommend satisfying the M3x8 DIN7380 (BHCS) screw with screws M3x8 ultra low profile ________________________ Purchase list necessary for the correct assembly of the mod: [1x] Sherpa Mini Extruder (BOM below), or: trianglelab - ...

In the case of the combadge, it has an uneven height on the oval, which I've corrected for by making it uniform. The interior of the oval is also not uniform, having a steeper curve in the center than it does on the left and right. The delta is...

In any case, using a 42MP body, such as the A7R II, stitching two (or better, three) shots will get you an approximately 48x36mm stitched image with about 84MP effective resolution. If you have a body like the Sony A7R IV, combining this with the...