sonoff s31 3d models

This allows you to desk mount the Sonoff NSPanel-EU. ...Print with the aperture down on the bed to avoid supports.

Here is a rewritten version of the original text: A Sonoff Tastamo Mounting Bracket for Installation in an Obi T60 AbZweigDose.

This device supports the secure and convenient mounting of up to six Sonoff Mini units on a single platform or within a spacious housing environment.

I designed this easy-to-use peg board holder for my Sonoff RF Bridge because it was constantly getting in the way and driving me crazy.

... ... Designed first to avoid the 1mm gap between the body of the sonoff and the wall due to the wall box. Then of course bring colours in the house. ... Please note that they were printed with supports, which could be a bit tough to get rid of.

The circuit board is from Sonoff (Sonoff Basic). No support needed. A V2 lid has been added, but the LED light is too bright, and an opening for a button is sufficient to see the light of the LED. ... An image of the enclosure has been added (it's...

I made this adapter to fit my SONOFF T4EU1C to a Australian light switch fitting. M3 nuts are fitted to the back of the plate. Screw the plate to the wall with original switch screws. ...Then fit the Sonoff switch to the plate adapter with M3 screws.

... on a standard Australian light switch base. ...The adapter's rear features M3 nuts, which can be securely fastened to the wall using original switch screws. Next, I attached the Sonoff switch to the adapter with M3 screws for a seamless integration.

Box for SONOFF 4CH PRO: Dimensions: - Box: 165 x 150 x 70 mm - Cover: 165 x 150 x 26 mm Connectors: - DC Male/Female Connector: https://www.amazon.com/dp/B00Z2LMT2O

I've a Sonoff Touch US model and front plate (it's made of glass) broke. So I designed this for replacing it. ... Remove all glass and glue paying attention, then attach this, I advice a good double-sided tape.

The Sonoff T1 switch needs a decorative trim to hide its exposed edges and mounting hardware. ...A custom cornice is the perfect solution to conceal these imperfections and provide a sleek finish.

I wanted to swap out my ordinary light switches for Sonoff Touch, but unfortunately, the Sonoff Touch EU are too big to fit inside a typical German double-flush-mounted box. So I decided to build a custom in-wall-housing that can accommodate two...

SonOff T1 US adapter for 503E 3-module flush-mounting box adapter. ... Resolution: 0.12 Material: PLA Printed: Creality CR10-S Infill: 30% P.S: Very high quality .SLT file.

This adapter plate enables easy installation of a T1UK 3 device Sonoff Touch Switch into a standard 3-gang light switch box, providing seamless integration and convenient control over your home's lighting system.

Lid that can replace the original one from Sonoff Basic R2 Attention / Warning : Il faudra compléter ce design avec une pièce empêchant l'arrachement des fils ("TabV3" de h0bb3 par exemple : https://www.thingiverse.com/thing:2791844/files). You...

SONOFF PIR2 PROTECTOR (2 designs) Protector for Sonoff PIR2 motion detector. ... To print: - 1 protector of your choice, with two possible designs available Assembly: - Secure the protector to the wall using 2 or 3 M2-20 countersunk head screws -...

The original frame is designed to fit perfectly with the SONOFF T1 EU, making it a great option for those looking to upgrade their smart home system. With its sleek and modern design, this frame is sure to complement any room in your house. ...Whether...

You can use screws provided with Sonoff to secure front plate and back; the button simply snaps into place. Wire guides keep wires neatly organized and in position. ...I recommend attaching 14-gauge solid wires, approximately 6 inches long, before...

I used this "Thing" to make a nice enclosure for some sonoffs I had: https://www.thingiverse.com/thing:2982177 With the Sonoff Basic R2 that I got, the toggle button on the sonoff was shorter than how the switch was designed. I made a little topper...

Meanwell LRS-350 + SonOff standalone case. Parts list Meanwell LRS-350 series PSU SonOff Basic Glass Fuse holder (for 5.2mmx20mm or 5x20mm fuse) Glass fuse (5x20mm) Rubble feet PG9 Cable Gland Strain Relief Optional Custom firmware for SonOff...

My design may match your needs, too.This module can be sourced from https://itead.cc/product/sonoff-re5v1c/I've included the STEP CAD file to assist people to incorporate the model into their designs. If you're like me, it doesn't matter how much...

... to shine through. This device makes an ideal companion for my Converging LED Floor Lamp project. ###Requirements: - 4x 8mm countersunk M3 screws - 2x 8-12mm button head M3 screws - Sonoff Basic R2 RF smart switch - Dual USB charger Model YJ-128

The backing plate on the Sonoff snaps into this (I used 6-32x3/8" screws with a nylon acorn nut on the back to shield the wiring for this). This plate can then be screwed directly into the four holes in the two-gang box, but you'll need longer...

My design may match your needs, too.This module can be sourced for around US$5 from https://itead.cc/product/sonoff-re5v1c/I've included the STEP CAD file to assist people to incorporate the model into their designs. If you're like me, it doesn't...

It has a small hole for the built-in button, so you should not be able to break the built-in button even if smashing hard the foot button (theoretically designed, not tested hard, and this may depend on your print, so keep it gentle :-)) The space...

... need for additional supports, simply print with the hole facing down. The panel can be easily mounted using two 1.5cm M3 wood screws, and the cable can be secured using the same. Upgrade your Sonoff NSpanel with this stylish and functional housing!

Box for one Sonoff TH10/TH16 with holes for two pg9 cable glands and a rocker switch. Room for temperature/rh sensor separated from board with a wall. Lid is thin around LEDs, and has a hole for accessing button on the PCB. Sensor has to be...

Update 01/10/2018 As requested by BlueMaster27, I've added a main body with fixing lugs and the Sonoff insert in one STL file 'Main Single Entry with insert and fixings.stl.' The Sonoff has also been raised by 1.5mm to make the button protrude...

To make a temporary connection to the Sonoff S26 programming pads, in order to reflash the firmware. This little jig which has spring loaded connectors installed makes reflashing the firmware to Tasmota or other firmware a one peson job. ... This link...

Sonoff Switchman M5 3-Gang module I designed the plastic button enclosures for above switch because in my first module order the middle button was broken at the hooks. ... On this occasion, i can create button enclosures of any color for this switch.