solids of constant width for sale 3d models

Amazon echo dot(2nd generation) holder for 25mm width(wire diameter: 5mm) metal wire rack.

Collection of solids made in Solidworks only for study purposes.

Collection of solids made in Solidworks only for study purposes.

This is 2U width (30 mm) version. Snaps on top of the monitor. It is quite strong not easy to detach. 1/4-20 camera mount screw is needed to attach camera to this mount. Base contains six holes for 3mm brass inserts. ...Holes are spaced 10 mm. This...

... 1/4-20 camera mount screw is needed to attach camera to this mount. Base contains two holes for 3mm brass inserts. Holes are spaced 10 mm. This allows creating adapters for mounting additional stuff, like microphone stand, light mount or else.

... 1/4-20 camera mount screw is needed to attach camera to this mount. Base contains six holes for 3mm brass inserts. Holes are spaced 10 mm. This allows creating adapters for mounting additional stuff, like microphone stand, light mount or else.

... 1/4-20 camera mount screw is needed to attach camera to this mount. Base contains six holes for 3mm brass inserts. Holes are spaced 10 mm. This allows creating adapters for mounting additional stuff, like microphone stand, light mount or else.

This is 1U width (15 mm) version. Snaps on top of the monitor. It is quite strong not easy to detach. 1/4-20 camera mount screw is needed to attach camera to this mount. Base contains two holes for 3mm brass inserts. ...Holes are spaced 10 mm. This...

... 1/4-20 camera mount screw is needed to attach camera to this mount. Base contains two holes for 3mm brass inserts. Holes are spaced 10 mm. This allows creating adapters for mounting additional stuff, like microphone stand, light mount or else.

... a precisely measured 30.2 mm gap. Dimensions: Gap between table top and headphones holder: 31 mm / 30.2 mm (tight fit version) Width: 20mm Maximum width of supported headset: 40mm Top part of the mount: 5mm wide Bottom part of the mount: 4mm wide

Adapter to fit pocket negatives into the standard negative holder of Epson Photoscanner. ... The size of negative is about 16 mm width.

http://www.thingiverse.com/apps/customizer/run?thing_id=1038261 Options Used: - Rotation of model set to -45 degrees - Whole message written as "hot" and "sale" - Scale in z-axis increased to 10 times original value - Model translated 50 units along...

You may use Customizer to run your own version too: http://www.thingiverse.com/apps/customizer/run?thing_id=263242 Printed with a layer height of 0.2mm, Infill solidity at 40% and Orange PLA in the pattern. Setting my print bed temperature to 80°C...

Base Design for Customizable Filament Spool Holder - Bearings and Versatile Width. Custom-Made Base for My Overclone 3D Printer, Perfectly Suited to My Needs. Vertical Mounting Capability for Standard 3060 Profile Printers. ... Note: Tight Fitting...

Here's the [tinkercad link](https://www.tinkercad.com/things/jpDYHc1bhQq-1kg-left-side-filament-holder-50mm-width-for-easythreed-x1) It's small enough that I printed it on the Sondori Pico (aka Easythreed X1 aka Labist X1) that it was being printed...

Visit Thingiverse's Customizer to personalize this design: http://www.thingiverse.com/apps/customizer/run?thing_id=245556 Customize your Pegboard Holder Using the following options: Peg Offset = 25% of Board Hook Width Percentage = 85% Maximum...

I urgently require a spool holder, so I adapted roady001's design to accommodate my specific spool needs. ...To achieve this, I increased the width of both the feet and the beam by 20mm.

This is a remix on the snap-on Airtag cases by AnonymousHermit. ...While I haven't printed it yet, this dog tag should fit on any collar with a maximum width of 1cm.

Axle Width Checker for 1:32 Slot Car - 64mm Generally useful for the Cartrix model. At our championships, this is the standard measure, which we've changed to accommodate different car classes. It can also be used as a stand for all 1:32 cars...

Axle Width Checker for 1:32 Slot Car - 57mm Typically useful for Cartrix models, which are a standard measure at our championships in the box cars class. Please let me know if any adjustments are needed and I'll make them as soon as possible. ... I'm...

Traffic light for the model (road width should be 13cm)The signal has three lights (green, orange and red) and floats on the road. ...It is easy to install with 3 screws.In my mockup, it is controlled by arduino uno r3.dimensions: 9cm x 5,1cm x 2,5cm

... i3 printer. ...To accomplish this, I'm using the PHIL spool holder as a foundation and adding a feature that allows it to be securely fastened to the metal top. Additionally, I've included a mechanism to adjust the width by simply loosening screws.

Big sale! ...A set of 8 horse murals \panno plus one beautiful wall key hanger! If you need a mural 3d model that is not in my portfolio - just send me a picture of the mural you need :)

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following settings: Additional tooth width is set at 0.2. The distance from the nut to the shaft is 1.2. M3 nut depth is fixed at 2.7. Pulley B height is 8 units...

The longer base is designed specifically to accommodate wider spools, such as the 95mm width spools found in the PRO series PLA spools from Matterhackers.

This pulley is ideal for electric skateboards that utilize a 48-tooth pulley on the opposite end of the drive system. ...A single 3m set screw is recommended for secure installation, but this may not be necessary if the motor shaft features a D-channel...

... for doors measuring between 60 to 110 cm in stroke length and weighing no more than 40 kg. The force applied can be adjusted within the range of 0.5 to 0.9 kg, allowing for smooth operation while also enabling users to customize the closing speed.

I designed those feet for my Anet A2 3D printer, but they can be adapted for any device based on aluminum extrusions. The adjustable height of up to five millimeters makes it simple to level your device horizontally. ...Secure the threaded nuts firmly...

SKU: OR025-02403A By printing this design and any variations thereof, the user assumes full responsibility of injury or death. This is a plastic mount that can be under great stress if not safely printed and used. ... Freecad file is given for user...

... which helped me create this model. Luckily, Hellerman Tyton has a large selection of models available on their website for reference purposes. ...For more information, visit https://www.hellermanntyton.co.uk/products/fixing-elements/tm1sf/151-40119.