solidex tripod quick release 3d models

Model made as 1/34. After being printed will stand - 281 mm tall, 716 mm wide, 1006 mm deep.FFF/FDM 1.0, FFF/FDM 2.0:- FFF/FDM 1.0 - old version (released back in 2016);- FFF/FDM 2.0 - new updated recommended version;- Сonsists of the top and bottom...

(Please excuse the poor prints, the black filament I had on hand was old and wet)Assembly - LTA Assembly - UTAYou will notice that lots of the things I have done are available in other remixes, there are a few reasons for this:I started this...

With that many people enjoying this design, I have continuously worked to do some slight improvements and released upgraded parts and add-ons over the weeks.Update 14.03.2022:For all my friends and followers in countries that use the imperial system,...

The LRM-10 missile launcher, Zeus-36 Autocannon as well as other armaments the Cyclops is equipped with are assembled in such a way that can be potentially replaced when the alternative Guns Pack for the Mech is released.The model is saved in STL...

(need to push to release) This way it would be easier to add software To top it off, the SD slot could be behind the disk lever, and add a power switch on the inside, operated by the lever. (this could be done by an eccentric disc that rotates...

The LRM-10 missile launchers, as well as other armaments Stalker is equipped with are assembled in such a way that can be potentially replaced when the alternative Guns Pack for the Mech is released. A separate Weapon Pack is already available for...

Makes you think about how well this printer was tested before release. The only way to fix this properly, while maintaining compatibility with both the single toolheads and the dual toolheads, without changing toolhead design, would be to increase...

Missile launchers, autocannons, as well as other weapons Warhawk is equipped with are assembled in such a way that can be potentially replaced when the alternative Guns Pack for the Mech is released.The model is saved in STL files, a format supported...

His ability to release energy rays from his eyes always frightened him, because he feared he could hurt people. There was a time when he doubted the correctness of Professor X’s judgments, which was the result of his hearing the speech of Magneto who...

 If you aren't interested in testing and giving feedback, please wait until enough people have tested it to be comfortable for a “full” release.  With that, I will be waiting to add the CAD files for this until it has been tested, just so...

After his release, he could not find a normal job and was forbidden to see his daughter. Because of this, he agrees to go on a new crime. Scott makes his way to the house but there he finds absolutely nothing of value and sees only the costume. At...

For the slider extender part released on the 30th of March 2024 - mirror the stl in your slicer otherwise it wont work.23.04.24 - Please don't print the hands3 angled up further (auf) - made a late night rookie mistake...forgot to adjust...

Despite being fatal, his iconic duel on Naboo with Qui-Gon Jinn and Obi-Wan Kenobi demonstrated Maul’s blinding speed and incredible agility.Today marks the release that we’ve all been waiting for - Darth Maul 3D printing figurine finally joins...

connector "7_Ge_Connector_A_A_x2" needs to be printed 2 times.FFF/FDM 1.0 version features:- The original version of MWO King Crab released in 2017;- The scale of the model is indeterminate;- Features outdated joints.You can get the model of MWO King...

... always fit in the standard SKADIS spacing. If you need some inspiration, checkout the Available models section to see which parameters have been used to generate them.Changelog:V1.0 (2022-09-25): Initial releaseV1.0 (2022-09-28): Updated description

 If using the TPU plate, I recommend using a smooth plate if possible, with some glue as a release agent, since TPU can really stick to PEI textured plates.  Remove any parts from the included profile, which you do not intend to use.Just a note on...

Due to the fact that this model was first released on Gambody in 2016 as a one-piece Armor with a solid Station platform, for all the Fallout fans to print the cleanest power frame possible T-60 was cut into many assembly parts and adapted for...

To prevent damage endstops are provided to set the fully open and fully closed positions. Note: This project is very much a prototype, has room for improvement and not really designed to be released into the wild. However some have shown interest in...

When finished you can remove the lid and clean away the plastic residue that may have released from the Chamber.Put the Chamber on to the Chamber and twist it into lock position.Screw the finished Lid knob onto the bolt in the Chamber lid to complete...

I can provide alternative parts for this if required. Spring: I purchased a 20mm spring initially which was too long and I cut it down, the 10mm I have is slightly too short so would recommend a 15mm or 20mm and cut if required. DockNote:...

Due to the fact that this model was first released on Gambody in 2015 as a solid one-piece motorcycle, for all the Ghost Rider fans to print the cleanest Devil Chopper possible it was cut into many assembly parts and adapted for different types of 3D...

It would help me and the community to leave a comment on how this version works to decide whether to release it or not.The file is recommended to print vertically with a layer height of 0.12mm and a 25% infill.It is necessary to cut the ptfe tube...

...After placing the source-spool firmly, release the wingnut (A), position and press the wheel to the spool and tie the wingnut (A). Test how well the spool turns, if it still runs to freely you can tighten up the screw/axis (B) to give more friction.

I use global variables everywhere, I don't release memory, or even initialize variables correctly. I know enough to know that I don't do any of it correctly. I just keep hacking on it until it works, and just barely most times. If you like this code...

That’s why stable structures in physics account for entropy, like a large gas engine releasing its exhaust through a turbine. Or at least this is the world as we know it today. The third law of thermodynamics could apply to civilizations as well....

has movable joints in feet and elbows only; hip, pelvis, and shoulder connections can change their angles;- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed;FFF/FDM 1.0...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

The 3D printing figurine's chosen scale is 1/8 for the FFF/FDM version and 1/16 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 3 parts;- A printed model is 100 mm tall, 72 mm wide, 83 mm deep;- The initial...

CAVEAT I will certainly update the software over time as ways to improve operation become apparent - so treat whatever release is there as an alpha. The design is robust in terms of electrical noise immunity but is sensitive magnetically - even...

It should not pop up under tension when released.[Optionally*] Glue the border and board pieces into the box bottom, starting with two of the black border pieces with pegs flush to the front right corner.  Remember that a White colour square...