sofle choc 3d models

Flip to get the left-side version.This is a low profile case for the Sofle Choc. It keeps the components and solder joints under the board from getting snagged on anything, while adding minimal bulk to the board. It’s great for using the board on a...

This is my attempt on a case for the Sofle Choc v2 keyboard by Josef Adamcik/Brian Low. I use the v2.2 Version from 42. keebs with an added power switch, but it should really work on any v2 revision. I tried to keep the case as flat as possible. ...

This design is a fun way to add a bit of color to your Sofle Choc, or to protect some of the exposed metal contacts on the underside. This design leverages M2 x 3.2mm x 3mm threaded screw inserts. Here's an example Amazon link:...

I built this so that my Sofle would be a little less naked than you get with the usual acrylic plates. This model is only for the Choc 2.1 variant with nice nano controllers and nice view displays. In addition to the keyboard itself you'll need:6x...

Created to work with this PCB: https://github.com/josefadamcik/SofleKeyboard/pull/104 In my screenshots, I'm using the encoders found [here][encoders] with a custom knob which is also on Thingiverse [here][knob-thing]. ... [encoders]:...

Tented case for Sofle keyboard

belongs to tobe. ...i dunno why it not there

Two case files for sofle v2 RGB keyboards.

Based on Sofle Carry Cases by givingco. Resize top cases to be printed on 15x15cm printer. Create holes to easy unfold. ...

A remix of https://www.thingiverse.com/Erdos "v2 Sofle RGB Tent Case" to use M3 size tenting legs instead of M4 since I had previously built some M3 tenting legs based on the IMK Corne build guide (https://imkulio.com/build-guide.html) I also added...

This is a fast and simple carry case for a Sofle version 1 ergoboard. It is designed to have ~3mm of eva foam added to pad it but it is not necessary, the fit is still nice. ...The design wont work if you have plates or encoder knobs that extend past...

I also redesigned the back plate to allow attaching wrist rests and have included the current ones I'm using.  In the pictures you can see the fully modded Sofle, I cut the new backplate out of  frosted 5mm acrylic as I think it looks nicer then the...

Simple Sofle V2 (https://josefadamcik.github.io/SofleKeyboard/) case inspired by https://www.thingiverse.com/thing:4720213 When printed in transparent PETG underglow works great, otherwise one could make some holes in the bottom for leds to shine...

A tray mount case for the Sofle v2 split keyboard. ...Note that this is designed for the actual version 2 of the keyboard, not the RGB version, which is sometimes referred to as v2.1 (and sometimes falsely as v2!) Check Josef's page for more...

I recently printed effae's Sofle V2 case but wanted a tenting solution. These legs give the case a 21.5 degree angle and have a nice wide base to securely glue them on. They are designed to fit between the screw by the thumb buttons and the inward...

WIP Tenting Case for Sofle Keyboard. The design is to allow for M5 bolts to be screwed in and used to adjust tenting. M2 spacers still required. EDIT: 26 Jan 2021 I was able to print a prototype and have added images The indents for...

This is a custom case for a wireless Sofle RGB split keyboard build. The bottom of the cases have slots for four 20x5mm magnets, which are used to hold the tenting legs and can also be used to attach the keyboards to each other as to make a...

Plates for the Sofle V2 Keyboard. 3mm thick. ...Happy clacking!

**END EDIT** You will need (4) M2 6+3mm Male-Female Standoffs and (4) M2 4mm Screws For details on wiring and firmware: https://github.com/foureight84/sofle-keyboard-pimoroni My other designs for the Sofle Keyboard: Base:...

This is a remix of the Sofle V2 RGB Beveled case created by thysdewet on thingiverse:https://www.thingiverse.com/thing:4753682/files It is intended to use M3 Socket Cap screws (3 per side) to attach the mount to the modded Sofle Case. ...It then...

High profile case for my sofle v1 keyboard. I wanted something more closed than sandwiched acrylic plate+bottom. There are holes for m2 inserts so the keyboard will stay in place. I'm planning to add rgb underglow so I've changed filament at 34 and...

... the underside of the PCB). My other designs for the Sofle Keyboard: Base: https://www.thingiverse.com/thing:4755855 Pimoroni Trackball Mount: https://www.thingiverse.com/thing:4756591 MCU and OLED Housing: https://www.thingiverse.com/thing:4784085

#**This doesn't work for v1 or v2 Non-RGB PCB's** **I included the STEP files in case someone wants to make modifications in their modeling software.** Tenting case for **Sofle v2 RGB** split keyboard. The **bottom layer** can be **laser-cut...

Pare choc Nikko année 90

Keycaps for Choc V1 mechanical switches.

Keycaps for chocs. ...Kinda funky, finger-cradling profile.

Using a tool helps unlock the Kailh Choc Switch (PG1350).

Voici un pare-choc pour voiture Nikko Gros buggy

keycap for the flat mechanical kalih choc switches

un pare-choc pour un chariot à pousser oxybul.