sofirn if25 3d models

Two flashlights combined produce an astonishing 5000 lumens when set to their highest setting. By applying gentle pressure, you can widen the beams, allowing for a broader area of illumination. View this accompanying video to see the setup in...

PLA Extruder: 210C Bed: 60C Infill: 25-50% Layers: 3 If you print in ABS, it is best to use a raft.

Goodman Holder for Sofirn SD05 underwater lamp. Available at: Amazon, Ebay, AliExpress. ... Fixed with 4mm elastic bands.

A simple base for the BLF/Sofirn LT1 lantern. ...The cutout in the bottom is for a ring of rubber or foam.

Replacement cover for USB charging port on Sofirn flashlights such as the BLF LT1, SP36, and Q8.Print with a flexible filament like TPU or flexible PLA.

My version of Sofirn LT1S shade. It just snaps on. ...Designed to be compact and have printable angles on virtually any printer (40º).

Socket flashing tool for Atmel ATTiny85. ...This was used to flash my Sofirn SC31 Pro flashlight. The access is extremely tight and this tool helped me a lot. See https://www.jaqpot.net/wp/2021/01/31/sofirn-sc31-pro-anduril2/ for more information.

A small shade for the Sofirn BLF LT1 Lantern. Gently directs the light downwards and reduces glare. Printed in 2 hourse with no supports at 0.1mm layer height. The low layer height improves the overhang. ... Category: Outdoor & Garden

Support for Blf q8 flashlights and Sofirn q8, also compatible with most sprays. ... 2x metric screws M3 *Note: A flat rectangle is included to place an identification label or a small logo that sticks with adhesive in this case.

An adapted version of a lampshade for the Sofirn LT1s lantern. Helps avoid glare and distributes light more evenly around the lantern, especially downwards. ... Created with OpenSCAD, printed on a FDM printer with PETG (transparent) or optional PLA.

The clamps are currently implemented for the following headlamps: D10/D20/D25 Sofirn SP40/SP40a YLP Panda 4 But if you need the holder for another flashlight, just give me the flashlight sizes and I will add the appropriate clamp. ... The platform and...

Just some flashlight diffusers. ...Printed with PLA and it didnt seem to melt. Has a small hole on top so it wont overheat. Works with the BLF Q8, Sofirn SP36 BLF, and Emisar D4v1, not sure v2 works but it may if it's the same diameter.

... after printing and process the landing site with a knife. The mount, like the original one, has a flashlight tilt adjustment. Attaches with two screws holding the top of the handlebar on the front. Sofirn H25L was purchased from aliexpress.

... in various situations. ...Sofirn's C8F mount offers a compact and secure way to attach a light source to any ferromagnetic surface, making it perfect for camping, hiking, or search and rescue operations where mobility and brightness are crucial.

Specifically, I am using this...

A simple base for the BLF/Sofirn LT1 lantern. There are two versions: v2: Wider, thicker version. The cutout in the bottom is for a ring of rubber or foam.</p> <p>v3: Slightly smaller and more minimal version. ...It is as wide as the head of the LT1 so...

... is simply yet effective. It fits my Convoy S2+, Sofirn SC31, Wurkkos FC11 or any other light with a 24mm bezel. It distributes the light evenly even on lower intensities. ...My tip for a great effect is to print with a glow in the dark filament.

Either the Sofirn BLF LT1 has a shallow tripod screw thread or (more likely) my studio light stand has one that's too long. I didn't want all the LT1's weight (and associated torque) to be borne by the brass screw's shank but figured that a simple...

Printable cover/box for the Wurkkos/Sofirn firmware flasher (attiny1616) sold by u/the_gchart on reddit r/flashlight. Makes it easier to hold steady without touching the electronics of the PCB. Made for the USB-C model. There are 2 versions: one...

The miniature shade for the Sofirn BLF LT1 Lantern takes center stage, expertly directing a focused beam of light downwards to minimize glare and maximize visibility. Crafted with precision, this petite accessory is printed in a remarkably short...

Caps 1 and 2 are to cover / protect all of it in one nice box.Hope you enjoy!seehttps://budgetlightforum.com/t/adventures-in-tinyavr-1-series/55911/322for referenceThese 3-pin flashing devices are for the newer Sofirn / Wurkkos / FireFlies lights...

The included design is for a Sofirn SP40 (or similar lights with more or less 22 mm diameter). You can modify the design using FreeCAD 0.19+. The printed clip is riveted to a piece of leather. A big light like the SP40 is too heavy to use without...

A simple lamp shade for the BLF/Sofirn LT1 lantern. There are two versions available: v1: My original idea, but my printer struggled with the 60° overhang at 0.2 mm layer height. v2: Slightly different design with a maximum overhang of 50° which...

The included design is for a Sofirn SP40 (or similar lights with more or less 22 mm diameter). You can modify the design using FreeCAD 0.19+. The printed clip is riveted to a piece of leather. A big light like the SP40 is too heavy to use without a...

Крепление можно переделать для sofirn SP40 и любые другие фонари. Исходники приложил. Детали крепятся болтами М3 длиной 10 мм. Либо можно просто склеить детали. Для соединения с резинками нужно распороть горизонтальную резинку с одной стороны,...

The BLF (Sofirn) LT1 is a very nice lantern, but sometimes the glare gets annoying. Wouldn't it be great to block the light in one direction? Now this is possible with this simple design that can be clipped to the LT1. You can use it either as is...

A simple lamp shade for the BLF/Sofirn LT1 lantern. There are two versions available: v1: My original idea, but my printer struggled with the 60° overhang at 0.2 mm layer height. v2: Slightly different design with a maximum overhang of 50°...

Sizes included as of now are: 14.2mm - suitable for Thrunite Ti3 and other flashlights 14.5mm - suitable for Lumintop Tool and other flashlights 20mm - suitable for Manker E11, Sofirn SP10A/B, Eagletac D25C, and other flashlights 24mm - suitable for...

Current sizes: 14mm - Lots of AAA sized lights 24mm - Wurkkos FC11 28mm - Emisar D4V2 29mm - Noctigon KR4 39mm - Emisar D4SV2 49mm - Sofirn SP36 52mm - Outdoor International K9.3 v2, thicker connectors added with tighter tolerances. ...STL naming...

The ribs on the mount do not allow the lamp to move.It consists of two parts: the base and the mount.The mount can be converted to sofirn SP40 and any other lights.The parts are attached via M3 bolts with a length of 10mm. Or you can just glue the...