sofirn hs10 3d models

Clip for the Sofirn HS10 flashlight designed to be used with the original elastic headband. ... Still a work in progress, any suggestion to improve is welcome.

Quick and crude design for mounting the Sofirn HS10 headlamp to my bike helmet using zip ties.I printed this using some crap TPU, because that is what already was on the printer, but this design will also work with PLA and PETG and so on...

A small holder for a Sofirn HS10 flashlight that clips onto an IKEA Skadis pegboard. ...

READ THIS FIRST BEFORE PRINTING I designed this headmount for the Sofirn HS10, because the original one is made from rubber and not suitable for running. It is very wobbly and the light shakes in front of you. I have printed and tested both...

Model of the Sofirn IF25 lantern. Scale 1:1. ...The dimensions are taken from the original.

A simple container for the fantastic Sofirn lt1s, allows you to insert the lantern inside and have a support to lift it in case of need. The container can be used as a glass and also has a cap. ... It's a simple print, you should have no problem.

Made a diffuser for a Sofirn SC31pro.

Mount for the Sofirn HS41 headlamp for GoPro mount

A diffuser for the Sofirn C01 flashlight. ...Print in vase mode.

Reflector for the Sofirn BLF LT1 lantern. ...I used duct tape for the reflective surface.

A diffuser for the Sofirn C01 flashlight. Print in vase mode. ... Category: Tools

For Sofirn Q8 Pro Flashlight Strap adapter PLA infil 40% 2mm screw---2

Magnet carrier for the Sofirn LT1S. Use 12 of the below linked magnets. ... https://www.kjmagnetics.com/proddetail.asp?prod=D7H1

Bike mount for the Sofirn SP33 flashlight. ... Fits 22mm handlebar and is lightly conical Designed in OnShape, can also be found there and modified.

Remix of tjmorrison's diffuser scaled to fit the Sofirn SP36, which has a 49mm head diameter. ... Update September 17, 2020 I have uploaded an improved model that greatly enhances the smoothness of the cylindrical wall.

Mount for Sofirn SP40 on 25.4mm handlebar (1 inch).Printed with PLA, 0.2mm layer height on Ender 3Holes are for M3 nuts and boltsEDIT: Added shorter mount

Good bed adhesion / first layer is required for the handle texture, print with a brim if you're having issues, everything gets connected together by layer 6.I also have handles forBLF Q8: https://www.printables.com/model/695265-blf-q8-handleQ8 Pro:...

A small tool for unscrewing the bezel on a Sofirn SP40 head torch. ...The indents in the bezel are quite small, so this print needs to be pretty accurate - I have access to a Formlabs Form 2 resin printer, but some tinkering might be needed on a...

A handy tool for effortlessly removing the bezel from a Sofirn SP40 headlamp is required. ...The tiny grooves in the bezel necessitate precise printing - fortunately, I have access to a Formlabs Form 2 resin printer, although some adjustments may be...

The Sofirn C8F is a top-notch light diffuser designed to deliver superior illumination while minimizing harsh glare. ...With its carefully crafted diffusing technology, this device ensures that light spreads evenly across the surroundings, making it an...

Diffuser for Sofirn SP31 (or any other light that is roughly 23.4mm in diameter). Needs to be printed in translucent TPU to work properly. I used 40% gyroid infill with 5 perimeters. I printed this in generic 85a TPU. Needs to be printed with...

Basic wall mount for flashlight. ...Two holes for mounting.I have not checked to see how long this mount holds up to use.Fits:Sofirn C01SMay require a bit of warm water to allow a good fit (May be slightly too tight)

This is a diffuser for the Sofirn SP 36 flashlight. I honestly have no idea if this is an effective diffuser compared to something built and sold by an actual company. I just thought it'd be fun to make and print. ...

This is a Lamp Shade for Sofirn's LT1s, which is the smaller brother of the BLF LT1 Due to a different design (no o-ring groove) the LT1 shade does not fit. The shade just sits on the lamp. Prints without support. ...I used PETG.

This is a handle for the Sofirn Q8 Pro torch, it been designed to require a single 1/4" x 12mm mushroom head Phillips drive bolt.Easy print with no support required. ...Good bed adhesion / first layer is required for the handle texture, print with a...

This is a handle for the Sofirn Q8 Plus torch, it been designed to require a single 1/4" x 12mm mushroom head Phillips drive bolt.Easy print with no support required. ...Good bed adhesion / first layer is required for the handle texture, print with a...

This is a diffuser for Sofirn's Q8 Pro. By design, the fit is tight enough that the flashlight can be hung from the integrated lanyard loop attachment point.&nbsp;</p><p>I printed this in esun GITD PLA with 10% gyroid infill and fuzzy skin (outside...

This is a simple shade for the Sofirn LT1 lantern. Honestly, there are nicer looking options out there, but I already designed this, so here it is. It's completely flat on the bottom, so no supports needed. It has an inner diameter of 35.65 mm. ...

This is a straightforward filter holder for the Sofirn SP36 flashlight, crafted with a flexible material like TPU or NinjaFlex in mind. Its purpose is to securely hold filter gels cut to a 48mm diameter circle, but be cautious when using these gels...

This is a simple base for the Sofirn LT1 lantern. It expands the base to approximately 4 inches to help reduce tipping. You'll need a 1/4x20 screw (1/2 inch long) and a hex nut. Inset the hex nut from above, tighten the screw from below, and then...