snowball mic stand 3d models

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...

I built a custom microphone stand for my Yeti Blue Snowball mic, giving it a sleeker look by making it shorter. ...The USB cable posed an issue due to its downward angle, but I found a solution that provides ample clearance for the cord while also...

I remixed the threads from  https://www.thingiverse.com/thing:3766117 onto a simple base plate for a tripod.

I remixed the threads from  https://www.thingiverse.com/thing:3766117 onto a simple base plate for a tripod.

This is a short desk stand for the Blue Snowball microphone. I designed this to be able to fit the mic below my monitors. The existing designs I found didn't have any space between the base plate and the mic meaning it wasn't possible to tilt the...

This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion 360...

This is a replacement part for the Blue Snowball mic stand. Factory plastic parts on the legs are subjected to considerable pressure, making them prone to breaking. To create this part, simply print with an infill of about 35-40%. No supports are...

Remix of clypp's design (https://www.thingiverse.com/thing:4315674) Used for the Blue Snowball iCE microphone, particularly for the models where you can't screw off the stand. This revision makes it so the parts wrap around the stand. Previously, you...

Blue Snowball Mic

Hey guy today I bring you a super simple yet really effective adapter for the SnowBall mic. I printed it with an infill of 50%. Subscribe to MrJefferson105. Print Settings are as follows: Printer Brand is Prusa, and specifically I used my Prusa Steel...

I had a snowball mic stand laying around and wanted to reuse it after I bought my mic boom. ...I have a new ender 3 pro and felt like this would be the best stand for a mobile phone based octoprint setup.

... part, as it contains M15.5x1.0 thread, which is pretty fine and could turn out not well enough). No supports required. This model is set remixed as the thread to the mic stand is taken from the 'Blue Snowball Mic Armature Mount' by Janbro. ...

I remixed a haxespot lamp to accommodate my blue snowball microphone, attaching it via a threading adapter borrowed from another user. I also created custom couplers to connect to the arm's end, ensuring a rock-solid setup. While the mic couplers are...

I needed a compact pop filter for my Snowball mic and wasn't willing to shell out $20 for a few dollars' worth of plastic, so I decided to print two mesh holders, attach a thin piece of fabric or mesh between them before assembling the model itself.

The Blue Snowball leg joint on the stand is not that strong. Designed in Fusion 360, simply print and screw in the new one. ... 30-40% infill with .2 layer height gives plenty of strength using PLA.

One-piece desktop mic stand

I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in Cura, so the legs printed quickly and the threads printed accurately at a high resolution. ... ...

this stand is compatible with all the standard mics

this stand is compatible with all the standard mics

Mic stand for Silvermonkey/Sudotack Anet A6 modded ABS 250*C h:0.25mm Total: 2h41min

Stand for microphones - I use an AKG p120, but most mics using the industry standard 5/8"- 27 threading should work. ...The black adapter in the picture was supplied by the manufacturer along with the microphone.

A mic stand which can be pieced together with a PCB pipe and some M8 screws. It is designed to be modular and foldable so that it can be put away in a corner or under the desk. I designed it to be used mounted to a computer desk for a mic with an...

A simple mic holder designed specifically for camera-mounted microphones that won't break the bank. Despite being on a tight budget, I've managed to utilize a camera mic for some recording projects with great success. However, after scouring various...

I'm using a Basic Adjustable Desk Stand to hold up my trusty Audio-Technica ATR-2500 Microphone.

I'm not familiar with many of you having microphones like this, or more specifically the stands they come with. But I have found the standard issue stand to be quite large and intrusive. So, I've made a smaller base that's easier to use. There are...

This is a minimalist tabletop microphone stand that's easy to use. Its exact height isn't specified, but rest assured it functions as intended. You might need additional support to get the best results. ...A new and improved model could be on its way in...

I needed stand for quite heavy microphone (PC microphone by Tracer with fancy “cage” suspension). It has 6mm wide tab with a hole that accommodates M5 screw - so it was chosen as stand's “interface”. FreeCAD project file is included so if you need...

I needed stand for quite heavy microphone (PC microphone by Tracer with fancy “cage” suspension). It has 6mm wide tab with a hole that accommodates M5 screw - so it was chosen as stand's “interface”. FreeCAD project file is included so if you need...

Very simple low desk stand for my snowball microphone.

This should fit any variation of the blue snowball mic, but if it doesn't just hit the hands with a gentle heat gun and use the mic to deform them to fit.