snow rc 3d models

... of my complete RC snow blower assembly. ...It was originally designed to fit with the Traxxas Summit RC car. However, I would recommend a larger RC car because the snow blower is to heavy for the Summit.Here are a few videos of it in action: 

... runs in snowy and possibly sandy conditions. ...My intention is to use them as a foundation for a comical-looking snow plow system, which will clear about an inch or two of snow from my driveway because I prefer not to exert myself physically that way.

Tracks for 1/10 Scale RC Cars, Trucks, or Buggies in Mattracks Style I Designed Them Specifically for My Vaterra Twin Hammers to Drive in Snowy Conditions The tread and axles come from a Tamiya 70100 Track and Wheel Set Check out my video of the...

Snow Skis for an RC Plane are designed to be approximately 7.5 inches long when printed. The scad file could benefit from improved commenting, and as a self-taught coder, I'm eager to provide further explanations if the community expresses interest.

I built the snow ski that can detach from the snow for flying off into RC airplane adventures. It will work well on electric airplanes with tricycle or tail dragger front wheels, attaching using the same 1/8 in. wire wheel struts. The SKIG file is...

This Is A Ski That Can Fly Off The Snow, Which Was Created To Suit Most Electric Rc Airplanes With Tricycle Or Tail Dragger Front Wheels Using 1/8 In. Wire Wheel Struts. The File For The Front Steering Wheel Is Included In This Package. After...

I live in Maine, so flying in the wintertime means snow. Obviously, skis had to happen. I've tweaked these to the point that I'm pretty happy with them. They look scale-ish and fly well. The only thing I'd say is that when landing, you might need...

This tiny snow blower is specifically designed to be used with a miniature RC vehicle, but it's possible that it might not fit or function properly on every single RC model out there.

For your RC helicopter, use snow shoes specifically designed for the Raptor skid tubes. ...Ensure a secure fit with a small 3mm hole to accommodate and tighten a grub screw.

Have you ever longed to drive your RC-car on snow or ice? With this design, you'll be able to tackle rougher and slickier terrain! Simply print out the part as many times as you need (I required around 20 per wheel with a diameter of 10 cm). You can...

... than the initial one. The first ski was replaced with an improved version that offers better balance. I removed the P2 part and instead used the factory nut on the RC car's axle shaft to secure it in place, as the original setup wasn't ideal.

RC Snow Tracks for 1/10 scale models. It should fit any car with a standard 12mm Hex Wheel Mount but you might encounter problems with body rub. (Only tested on Axial Capra) Video : https://youtu.be/1Dnh0IAAjnM Google drive link containing :...

12mm hex snow/sand paddle wheel. Modeled based on stock Traxxas slash wheels. If printing with TPU or similar, make sure to print the separate insert and washer out of a harder material (PLA). The hex of the single piece model will probably strip...

Designed a multi-piece Snow Ski design that uses 2 parts that are repeated in design. No need to print a left side and a right side separately. Break the ski? Reprint the bottom portion instead of a single one piece unit. The base ski has...

This is a remix I made of totofendt snow tracks with a few changes/additions; 1. Uses 6003 bearings (17x35x10). You could still print a bearing if you wanted a printable one. I found printable bearings and grass/dirt don't nix well. 2. Added...

... Noree's Open rc f1 car. ...It includes snow tires for the rear wheels and skis for the front. It's really simple but a lot of fun. Watch it drive and the build guide here: https://www.youtube.com/watch?v=cii2E4xWl5k Happy Printing! .../3Drcnc

Made some snow skis for the arrows rc bigfoot. I usually don't make a tail ski anymore since it just drags in the snow like the wheel does. Just print 2 of these skis, they are the same for left and right. After you print them, you will make...

It includes snow tires for the rear wheels and skis for the front. It's really simple but a lot of fun.</p><p>Watch it drive and the build guide here: <a...

I am offering you my snow blower, which I have painstakingly constructed.All files on:https://cults3d.com/de/modell-3d/spiel/rc-schneefraese-rc-snow-blower-1-10The model was a Kahlbacher KFS1050 (but not a 1:1 replica).The snow blower is in 1/10...

for use with rc snow track Champagne Yeti track this link use less of material TPU and more lightweight can be linked with nails of finition 16 ga 2 1/2 length or for not so powerfull truck like as crawler 1/10 with stock motor you can use carbon...

This is a plow for the Aliexpress RC wheel loader. ...This plow is designed to attach to this loader only as the mounting is set for this machine.

I designed Snow Wheels for my monster truck and crawler. They feature a sturdy 12mm hex bolt. The wheels measure 120mm in outer diameter and 60mm in width. If you appreciate this design, please show your support by leaving a "like" - it will mean...

I'd created Snow Wheels for my monster truck and crawler. They've got a 12mm hex. Outer diameter: 150mm Width: Front: 90mm Rear: 120mm They are designed for the right side of your vehicle, so if you need them for the left side, simply mirror their...

Skis printed in 3D that can be used on remote-controlled planes to soar through the snow. Successfully tested on a tail dragger, but should also work for three-wheeled model aircraft. Multiple options are available, including skis with and without...

They are compatible with standard 1:10 RC torque transfer nuts (12 mm) and have a hole for a 4 mm shaft. For optimal printing, use 0.2 mm layer height, 0.5 infill, ABS plastic and print two of each wheel type, flat side down. Support may be helpful...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/9HWha58gFi0

I upload the scad version of the bearing. I recommend printing the drivewheel first and measuring the shaft diameters to adjust the bearing dimensions (outer diameter and ID). As the drivewheel is printed vertically, the diameter resting on the plate...

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

idk i made it i live in ny so this shall work

Отвал для трактора или монстр трака