snow plow for traxxas slash 3d models

The design is specifically tailored for the Traxxas Slash 1/16 model, but it can potentially be resized to fit a 1/10 scale model by applying a simple calculation: current size multiplied by 16, then divided by 10. I obtained the tire designs from...

Ever wanted to attach a Traxxas Sledge wing to your Traxxas Slash 4x4 that you converted into a BackSlash? Well, you will now after printing my simple, bolt-on solution! I designed this part because I wasn't the happiest with just running bolts...

You can push this plow easily at walking speeds, and because it pushes the snow to the side, you never have to lift it. Your back will thank you. Good for snow up to 8" deep. It works best on snow that hasn't been compacted yet, but you can muscle it...

You can push this plow easily at walking speeds, and because it pushes the snow to the side, you never have to lift it. Your back will thank you. Good for snow up to 8" deep. It works best on snow that hasn't been compacted yet, but you can muscle it...

You can push this plow easily at walking speeds, and because it pushes the snow to the side, you never have to lift it. Your back will thank you. Good for snow up to 8" deep. It works best on snow that hasn't been compacted yet, but you can muscle it...

... 2 parts that should fit smaller printers just fine. I also included 2 small pegs on one of the plows to make gluing or fusing it together much simpler. If you'd like, I can add another file with the entire plow in one piece for added convenience.

I also lowered the hindge point of the plow to compensate for larger tires as well as changed the light mounts and widened the plow blade by 40mm to match my track width. ...also extended the frame mounts further back to make the connection stronger...

A barrier designed specifically for use on a 3D-printed snow blower.

- Fits Traxxas Slash 1/16 Scale Model Cars Perfectly. - Should Be Easily Resizable to 1/10 Size by Multiplying the Current Size by 1.6. - Tires Were Remixed from https://www.thingiverse.com/thing:4326258 - There Are Three Versions of Tires Available:...

The imbalance between the front and rear of the Traxxas Slash 4x4's original body was a major issue that required attention. I modified leftover parts from the stock body mount using extension body posts, cutting them down to size to raise the front...

I've designed a battery spacer for the Slash 4x4 specifically to address the problems associated with the foam spacers that come with this RC vehicle. These foam spacers often cause wear and tear on the RC over time, making it look aged and worn out....

The model's dimensions after assembly are: 270x80x125 mm (10.63x3.15x4.92 in) If you like to experiment with this model on other track scales, the factors to match them are: x0.847 for 32 mm track (scale "0") - x1.19 for 45 mm track (scale "G") -...

A future version will boast an enhanced V-shaped bottom for improved steering performance, so stay informed about updates. Update - the latest iteration, suksi3v2.stl, showcases enhanced steering and clearance. ...

REQUIRES NO GLUE FOR THE TIRES there are "locking lugs" on both wheel and tire to keep it from rotating on the wheel. (6) 3x12mm screws are required to assemble wheels. These smooth wheels are designed to fit the rear of 2wd vehicles only. ...If you...

This high-tech truck is ready to roll out and tackle a snowy day, equipped with six powerful wheels that drive a double plow capable of slicing through even the thickest snowfall.

I had to cut away much of the driver's side plastic to free it up for a good view but it works pretty well.It is set up to mount a 9g servo on top (base of most pan tilt setups).You'll need to drill holes to mount it. ... I used m2 hex bolts/nuts.Short...

This does not work for the new baya croc but i will create one for that croc

... scoop is made from a heated ABS plate that was then bent into shape.\n\nAttach to the pushrod mount with screws. ...A winch is used for lifting and lowering.\nThe upper reinforcement is achieved through threaded rods\nMaterials Needed\nABS Plastic

Crafting a precision-fit snowplow bumper for miniature vehicles demands meticulous attention to detail and an unwavering commitment to authenticity. Model makers seeking to create highly realistic winter scenes must consider the intricacies of...

Fjärås of Sweden snow plow

Snow plow on a tractor

Hanger for a Boss snow plow control. ...Mounting ring is 21.8 x 1.5, the center ring is 10.15 x 3.85 and the retainer is 15.9 x 3.

Redesigning the Bruder Truck Snow Plow for miniature 1/25th scale vehicles requires careful attention to detail and a deep understanding of the original design's intricacies. By making deliberate modifications, it is possible to create a functional...

An accessory crafted for Brio/Thomas style wooden trains replicates a snow plow from "Adventures of Thomas." To avoid getting stuck on slopes, the blade's bottom edge is tilted up. While it connects well to several trains naturally, a small ceramic...

Check out this awesome RC4WD Snow Plow Plastic Base on YouTube - https://www.youtube.com/watch?v=-VUHc9P5KuT. It's super cool, and I've heard it's a game-changer for off-road enthusiasts. The plastic base is sturdy and durable, making it perfect for...

Here is a model of a Skidsteer Six-Way Snow Plow. Although fairly modeled This is an untested design, and has missing hardware and hydraulic components. ... Fabricate at your own risk.

... to address that problem. I've yet to figure out how to install a servo for automated lifting, but manual operation worked surprisingly well - just back up and push forward, and the weight of the snow will do the rest. ... Check out this video:

I would recommend printing in PETG for added strength, but if you don't use the plow as a battering ram PLA+ holds up pretty well. For added traction, you might want to consider tire chains. I made mine out of some small jack chain I bought from my...