sniperscope 3d model

The Version 1 is based on the original model, but with added material to compesate the extended face on the striker, and the second one is something I made because one of my magazines was giving me trouble, not really stoping when it needed. See what...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

A customized version of this Thingiverse model (http://www.thingiverse.com/thing:46884) was created using Customizer. ...The STL file options include: qr_rotate=0, add_sub=2, hole_r=10, hole_y=0, hole_x=30, corner_num=1, qr_thickness=5,...

Update 220811:Added solid with 1deg step on requestReplace the code below to this, (BB and CC changed to 2 and 1 and replace STL to the new...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...

It features several small niceties, such as a water inlet that optimizes top-water removal, using magnets instead of suction cups, a 'vacation' mod for skimmer waste overflow, snap-on piping for secure fitting, and much more.Please note that this is...

There seem to be quite some error margin in production, if your model is a bit too big to fit, just sand off maybe .5 mm from the sides to make it fit.Completely(!) remove any filament remains inside the two enclosure parts.Fit servo into upper half...

Thank you very much and happy printing!Updates13/02/2022: Redisegned T-Slot-Clip so that the PTFE tube does not interfere with the cables on the side of the Raspberry Pi (see picture below).PrintingLayer height: 0.2 mm;Material: PETG (recommended),...

*Download new version 1.01 here: https://www.printables.com/model/178925-ender-3-s1-stealth-light-bar-easy-to-print-and-do-mod ( Maintaining on Printables ) Easy to print light bar that uses the built in accessory port for power. This allows for...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 custom_case_wall_thickness = 1.6...

The retainer is up higher than need be in the video for safety.--------------------------------------------------------------------------------------------------------------All parts printed in PETG, with standard Voron settings for rigidity.0.20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

Theoretically, it can run more than 11 hours on 1 load (not tested). What parts do you need?Plastic parts:You can use the print files if you have an MK3S or you can use the model files and set everything up yourself. The photos show the position...

The “NANO 1” model follows (support for matrix / hemera already published). in addition to the name and logo (grant it to me) they share the same "SUPPORT BASE" component as a fixed base, and with the quick release (only 2 screws) to adapt in the...

No support is needed and would be very hard to remove because the support would be inside the model where the magnet eventually slides into. We are depending on bridging for the parts that would normally need support. I have given extra tolerance...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

Downloaded some Radio Control model yacht designs. Non of them suited my fancy for building, so I decided to come up with my own. Main Desing principles... No Keel! -> Surf Board / Windsurfer style. Light Weight (relative to size of jib!) ...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

I added some build notes below and a BOM which doesn't include screws, wires, connectors, etc., but has all major components. I planned to revisit this model and release a better version. However I have at least a year's worth of projects in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

Do not purchase unless spare parts are easy to get; not all parts are easy to CAD model or print. OEM replacement parts for the q905 can be found [here](https://www.hosim.com/collections/parts-for-q903).You can also take the OEM part number and...

The STEP file is included for easy remixing. Please post any makes and if you see a problem please post a comment. Updates: 4-30-2020: Thanks to feedback, I corrected the model for the base, the updated version is "6I". ...None of the other parts...

In order to ensure that the 2 rhombi are assembled correctly, there are 2 different tabs built into the edges of my models. This ensures that they'll only ever be joined correctly! Also, the strips make it visually clear how to assemble them.</p>...

... pictures are from Printable Heroes. They do not sponsor nor endorse these stands, but they do indeed offer a great variety of models —many of them for free. ...They do also have several, very affordable Patreon tiers —I suggest to check them out!