snapmaker octoprint 3d models

Universal Filament Spool-Holder - Designed for Snapmaker A350. - Suitable for all filament-spools with inner diameter from 45mm up to 85mm. ... - Diameter above 85mm are possible but not tested.

This is an elbow for the enclosure on the Snapmaker 2.0. ...I would imagine most of you have your printers on a desk like mine and attaching a flexible duct for the exhaust fan was a bit tight.

A bumper created to be attached to Snapmaker 2.0 Y Linear Module's end where the hot bed cable can potentially get caught, thus causes printing mat to be shifted.

For testing if it can slide into your Snapmaker 2.0 enclosure frame. ... It might be difficult to slide in for the 1st time, just don't give up too early.

Fan adaptor to replace to stock fan of the Snapmaker 2.0 power supply (PSU) by a 40x40x10 fan without replacing the backplane. ... I tapped the part for M3 nuts/screws.

3D Model of Snapmaker 2.0 3D Printer tool head for making add-ons/mods. ...May not be 100% accurate, but should be close enough to modelling exterior add-ons.

Stuck my SnapMaker 2.0 power supply with Nano tape to the underside of my table. This bracket is a safety feature should the tape not hold. ...The Nano tape I used is about 2mm thick.

Power Supply mount for Snapmaker 2.0. Needs to be printed twice and can be mounted to just about anything. ...I mounted mine to the back of my enclosure and it fits nicely.

This bushing clips into the Snapmaker 2.0 Enclosure's filament passthrough bushing and holds a short section of 4mm OD PTFE tubing to reduce friction from the filament sharply changing direction.

I want organize wires under my desk. ...So here is 3d printed clamp for Snapmaker Original Power supply LYD LIANYUNDA MODEL LYD2405000I used PLAand Fast print option (Infill was 20%)

Created spool holder for the new dual head print module from Snapmaker. ...The holder tube that came with the Dual Head is shorter (70mm) than one that came with SM 2.0 machine.

A shorter version of the Vacuum Attachment to work with the original snapmaker 2 enlosure. ... The original version is too long so with an attached hose it will fall off during homing.

This is a corner brace designed for use with the snapmaker 2.0 CNC wasteboard. ...The hole spacing is 50 mm, and the hole diameter works with the M4 bolts included with your machine.

The Snapmaker 2 enclosing provides no space to store the filament. ...Just snap the holders into the top left horizontal bar of the enclosing and out the filament roles in place.

This is great way to hold down basswood for lasering on the Snapmaker. This particular one is designed for 2.5mm thick 11-11/6" X 8-1/4" Basswood I bought. ...Hope it helps!

This is for stopping your spools from snagging onto the Snapmaker Original's spool holder, while it is attached to the enclosure. ...It happened to me twice, so it was not a coincidence, therefore this little stopper.

##Snapmaker 2.0 GoPro Mount for Logitech C270 at first you need: 1. https://www.thingiverse.com/thing:4939279 (Mount for x-achs) 2. ...https://www.thingiverse.com/thing:2439520 (Adapter for C270 of GoPro)

STL Model of the CNC Spoil Board for the SnapMaker 2.0. Helpful for laying out parts for machining and / or generating fixtures and jigs. ... Please let me know if anything is out of place.

Wyze Camera Perch that mounts to Snapmaker A350 enclosure. Hole to run cable through. Pocket to drop in the wyze camera magnet for an even stronger hold. ...Can be mounted low as shown or high in the upper corner.

A guide cap for inserting the output boarden tube of Mosai palette into the extruder of Snapmaker. ... The screw diameter is a general M6, and it may be necessary to cut the tap depending on the output condition.

I run a filament drying box inside the Snapmaker 2.0 Enclosure and rote the filament up and over the filament spool holder that comes with the Snapmaker 2.0. In preparation for the dual-filament print head and being able to string two different...

... vertical space. I used 6 pieces total. Remixed from: https://www.thingiverse.com/thing:4643756 Print Settings Printer: Snapmaker 2.0 A350 Rafts: No Supports: No Resolution: 200 Infill: 15% Filament: eSun PLA+ Black Category: 3D Printer Accessories

... to hold the 3D printer module with the 5015 fan mod. The rack also has slots for cnc router bits, the included snapmaker tools and clamps. The holder is designed to fit on the A250 bed. ...Depending on settings, print time is about 40 hours.

... using 3mm diameter screws / bolts with less than 5mm head. Will work at the required depth with Snapmaker screwdriver. Plates stack above each other, will upload photos once printed and attached. ... Feedback welcome as this is my first design.

Bien que ça ne soit pas une copie je me suis inspiré du très beau travail de (Snapmaker Filament mount by MrFen August 19, 2020) https://www.thingiverse.com/thing:4573894 Merci à lui pour cette bonne idée. ... Le support peut-être fixé en imprimant le...

... my provided drawing. This design is intended to accommodate four cables folded into a "Z" shape. You can use the same screws as those used for the Snapmaker: M4 x 8 or M4 x 10 (ISO 14580/DIN 7984) along with matching hex nuts (ISO 4032/DIN 934).

... and 22 hours of printing time with the settings above. There is also a version for Snapmaker Original which you can find here: https://www.thingiverse.com/thing:2792624 Happy to receive any kind of feedback and ideas for further improvement.

... for easy modification. Tested with initial layer height 0.3mm and general layer height 0.25mm. Used Snapmaker Luban profile "normal quality" as template. ... Hint: Stick a tape between this part and the linear module to close the remaining gap.

... vertical space. I used 6 pieces total. Remixed from: https://www.thingiverse.com/thing:4643756 Print Settings Printer: Snapmaker 2.0 A350 Rafts: No Supports: No Resolution: 200 Infill: 15% Filament: eSun PLA+ Black Category: 3D Printer Accessories

... on a suitable solution. Everything you need: 4 x 4x8mm screws (from Snapmaker)4 x screw nutsI'd be happy about your feedback!Follow me on Instagram @hard.holzIf you like my construction I would be happy about a small donation paypal.me/memmentaler