snapmaker filament 3d models

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

I built a spool adapter that's fully customizable due to its parametric design, so feel free to modify it to fit any spool with an inner diameter you happen to have on hand.

In my case I found it being a convenient place to put filament spool, however only a single screw would make spool arm unreliable and unstable, so I made this part that keeps it solid at optimal angle. ...My spool is now always dust free and I believe...

https://youtu.be/7jxEEzbDo9s?si=cYBOD4Hl-5b9lZYA Ich habe die Position der Filamentrolle grundlegend angepasst. Als erstes habe ich den originalen Halter wie auf dem Foto zu erkennen innerhalb vom Gehäuse montiert. So ist die Rolle von Staub und...

But I had changed where the Snapmaker Spool mounting bar hardware was located on the enclosure. I put it on the back of the enclosure flat against the back acrylic panel. See pictures. While the original design worked fine, it was hard to...

(I measured several filament spools from different brands I own) · Compatible with spool up to 160mm deep. · Quick swap without take parts off · Very smooth rotation, self-balancing · Minimal bearing requirements ` Good impact resistance ...

Customized version of https://www.thingiverse.com/thing:2997350 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2997350

Customized version of https://www.thingiverse.com/thing:2997350 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2997350

Customized version of https://www.thingiverse.com/thing:2997350 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2997350

I fitted the original part to match the SnapMaker's included filament, but when switching to Hatchbox, I had to modify it to accommodate their size. ...To make this work, I tried using Openscad to tweak the design, although my inexperience with the...

Filament spool adapter upgrade with precision ball bearings for your Snapmaker 3D printer. The inner diameter of the reel is Ø53 mm, accommodating a wide range of filament widths. To ensure compatibility, supported reel width is approximately 50-65...

I remixed for Snapmaker 2.0(A250). Small inner diameter provide smooth spool rotation. You can edit Fusion360 (.f3d) file sketch for own printer spool shaft diameter,length,etc... Category: 3D Printer Accessories

I remixed for Snapmaker 2.0(A250). Small inner diameter provide smooth spool rotation. You can edit Fusion360 (.f3d) file sketch for own printer spool shaft diameter,length,etc... ...

As an alternative part of the existing filament inlet, use PC4M6 fitting as PTFE adapter./

Purchase the necessary part, the Straight Precision Linear Shaft (MISUMI) SFJ5-270. ...Order it online at https://us.misumi-ec.com/vona2/detail/110302634310/?PNSearch=SFJ5-270&HissuCode=SFJ5-270&searchFlow=suggest2products&Keyword=SFJ5-270

Customized version of https://www.thingiverse.com/thing:2790108 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2790108

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

As I wanted to put my Snapmaker 2.0 A250 enclosure with its back to the wall, the clearance of the original filament holder (and the spool) was too much. When turning the filamentholder pointing to the front, the arm of the holder interferes with the...

This is a remix of the filaguide vor Snapmaker 2.0 enclosure from petitdragen21. I made the gap wider, so you can insert a 4 mm bowden tube. I installed a bowden tube between my toolhead an my filabox on the top of the enclosure. ... As a result of...

This works with the holey filament holder in this link: https://www.thingiverse.com/thing:4848261 I used a bit of glue and had it sit as far out as possible and angled to allow the easiest path for the filament to enter, then used this pipe kit :...

Filament Roll Holder Rail for Snapmaker - Designed Specifically for a Standard Filament Roll Dimensions: Outside Diameter: 200 mm Recording Diameter: 53 mm Width: 72 mm Additional Required Components: Four Ball Bearings with the Following...

You should cut the bottom of the J1's silicon nozzle cleaning pad a little bit to shorter and cut the outer protrusion of the quiditech box' lid and fill it with silicon etc. so as to seal it. ...Also better just cut the inside protrusion of the box'...

Customized version of https://www.thingiverse.com/thing:2997350 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2997350

Customized version of https://www.thingiverse.com/thing:2997350 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2997350

Remix of https://www.thingiverse.com/thing:4504481 and https://www.thingiverse.com/thing:4175157. ...With a additional support leg and a hole for bowden tube 6mm.

Remix of https://www.thingiverse.com/thing:4504481 and https://www.thingiverse.com/thing:4175157. ...With a additional support leg and a hole for bowden tube 6mm.

This is a very small remix of an incredible Snapmaker filament holder. ...I just closed the old holes and added 2 new ones to fit the mount for the Tapo C100 Security Camera.

This is a very small remix of an incredible Snapmaker filament holder. ...I just closed the old holes and added 2 new ones to fit the mount for the Tapo C100 Security Camera.</p> Category: 3D Printer Accessories