snapmaker filament 3d models

Snapmaker 2.0 Wall Mount for CNC-Head with Snapmaker Vacuum Attachment I designed this wall mount for the CNC-Head of Snapmaker 2.0 with their provided Vacuum Attachment installed.

030.003.001_01_+0.1 (+ ~ more clearance) 030.003.002_01_-0.05 (- ~ more clearance / + ~ less clearance) 030.003.003_01_0 (- ~ more clearance) / + ~ less clearance) The tolerance of part [030.003.001] only refers to the mounting of the adapter...

... Internal recirculating air filtration unit coming soon! Check out my ongoing Snapmaker Forums post on the other mods I have on my machine here: https://forum.snapmaker.com/t/cnc-bracing-for-added-rigidity-other-mods/29444?u=elliot

Prevent the Heated Bed Cable from catching on the end of the linear module on the Snapmaker 2.0. This design is to compensate for the small space available when the printed bed is all the way back in the A350 Enclosure. Tip: Snap the chain link...

UPDATE: some holes and dimension adjusted for a better fit Holder for the side profile for the Snapmaker 250 housing. This holder is mounted on top and places the display on the upper edge of the door. My case is on a stand and it is tedious to...

... doesn't start immediately. That is normal Please do not install some original components, otherwise the air flow will be hindered (see pictures). I am not responsible for any damage to your Snapmaker. ...Everything you do is at your own risk.

Rotary Y-axis for Snapmaker 3d printer. This is a must-have if you need to laser engrave on a cylindrical object, as it keeps the focal point at the same distance. Print 2x Rotary Y-Axis part 1.stl and 2x Rotary Y-Axis part 2.stl. Hardware...

This is a dust fence for the Snapmaker 2.0 A350's CNC function. Even though I do have the stock enclosure, I still don't feel like having dust flying everywhere in it. And the vacuum does not catch 100% of the dust, so I decided to create this...

Simple little pull-tab 'handle' to make it easier to "buckle" the Snapmaker 2.0 A250 Enclosure sliding door at the outward part of the tri-fold, while opening. Printed in PLA with 2 layers or so (0.24mm layers) top, bottom, and sides, and 15% or...

These are designed to be printed with the Snapmaker itself and then attach to the laser bed plates and/or CNC board so you can quickly swap among 3d printing, laser, and CNC without removing the heated build plate. This is an updated and very much...

The ends of the thick frame sections on the snapmaker enclosures are open. This adds holes in the enclosure letting out heat and fumes (and does not look very appealing) so I designed these simple covers for the corners. I designed these for my...

After seeing the price of the filter made by Snapmaker I decided to make my own. This filter will connect to the hose provided by the enclosure for the v2.0 350 model. I used 2 HEPA filters which I sourced from Amazon. I wanted to make sure there...

This is an upgraded arm designed specifically for the SnapMaker Pi Cam holder, enabling you to securely attach the camera to the X axis and track print jobs from start to finish. This feature is particularly useful for taller printed objects,...

Snapmaker advises against printing PLA with the top panel on the printer, because the environment heats up which can cause heat creep. If you still want to be able to use the top panel on the printer while printing PLA, you can use these risers. They...

I received my Snapmaker 2.0 A350 enclosure a week ago after having my printer for 8 months. Since getting the printer I've been using Octopi to control and monitor the printer. I couldn't figure out a good place to locate the octopi so I fired up...

Snapmaker 2.0 A350 Enclosure Touchscreen Mount - Base of mount can move along the enclosure rails - Mount can spin 360 degrees through the use of a bearing Amazon components: 1) Brass Knurled Nuts Threaded (M4) -...

This is for a 3.8mm high bed that is just slightly (0.5mm) larger than the Snapmaker bed in all dimensions. Make sure to only adjust inner walls and not outer walls, as adjusting outer walls may cause them to run in to the Z axis rails. ... One...

A simple cap for the display hole in the Snapmaker 2.0 Enclosure. I've fixed my display in another location outside the enclosure (last picture) and this left a hole where it was by design which isn't best when using the laser head or printing...

Adapters to connect the Snapmaker bed frame to the linear rail guide supports. This upgrade adds supports at the front and back corners of the bed frame to prevent bending down during actions at the limits of the vertical axis Version 4 will...

This is a laser cross that I designed for the Snapmaker 2.0 10W laser. I got tired of trying to find the center all the time, especially with glasses on. Simply print this out, wire two of the lasers (below) in SERIES, and connect to a 5v power...

Modèle d'aspirateur CNC pour turbine 60W Paramètres d'impression sur snapmaker (pour les grosses pièces) layer height : 0.3 mm wall thicness : 0.8 mm top / bottom thickness : 0.8 infill density : 15% print speed : 80 mm/s Les pièces "cyclone part1"...

These Brackets secure the CREALITY 310mm x 310mm x 4mm Glass to the Snapmaker 2.0 A350 bed. As we all know the A350 bed is very bad for flatness, mostly around the outer 50-75mm. This helps, but my end goal is to shim the heat plate to flat and...

The Bucket is the same as in the original, the holder was redesigned to fit a Snapmaker 2.0 (should work for all machines, but I have a 350). In any case the aluminum what you see is an Illy Coffee can cut into shape and the white is a teflon [I...

Prevent the Heated Bed Cable from catching on the end of the linear module on the Snapmaker 2.0. This design is to compensate for the small space available when the printed bed is all the way back in the A350 Enclosure. Tip: Snap the chain link...

Description Vinyl cutter for the snapmaker 2.0 Instruction Bill of material: 1x 030.006.001 (Print individually with raft.) 1x 030.006.002 1x 030.006.003 4x THK LMU5 "linear bushing" (*) 2x MISUMI SFJ5-75 "linear shaft" (*) 1x rubber band 1x...

May not be as necessary on the Snapmaker 2.0 type system, with the print head only moving in X and Z, not Y (the table does that). But with the added enclosure and the grommet thru the side panel providing another friction and choke point, I feel...

- 8 pcs m4 nuts - 8 pcs 19.05.23: Adjusted the positions of the mountingholes on the covers according to specs from Snapmaker. 20.05.23: Added missing nuthole. Adjusted accesshole to mountinghole on the covers. Changed the shape of the...

This is some basic mounting options so you can attach your Snapmaker 2.0's power supply to the back of your Snapmaker 2.0. There are multiple ways to mount this using these files, so pay attention. |Part|Description| |---|---| |Power Supply...

Print Settings Printer: Snapmaker A350 Rafts: No Supports: No Resolution: .2mm Infill: 20 Filament: MatterHackers PETG Translucent Green Notes: Designed to be printed with a .4mm nozzle printing specifically at .2mm (or less) layer height, there are...

Print Settings Printer: Snapmaker A350 Rafts: No Supports: No Resolution: .2mm Infill: 20 Filament: MatterHackers PETG Translucent Green Notes: Designed to be printed with a .4mm nozzle printing specifically at .2mm (or less) layer height, there are...