snapmaker enclosure 3d models

... The result is a simple, reliable and convenient solution. Later I added a new version for ease of installation. - Hole diameter - 12mm (fits to standard side hole in Snapmaker 2.0 Enclosure too) - 2x PC4-M6 PTFE connectors can be installed

This is a remix of the filaguide vor Snapmaker 2.0 enclosure from petitdragen21. I made the gap wider, so you can insert a 4 mm bowden tube. I installed a bowden tube between my toolhead an my filabox on the top of the enclosure. ... As a result of...

This is a remix of Rocinante2's [Wyze Camera Mount for the A350 enclosure](https://www.thingiverse.com/thing:5234172). I slotted the bottom hole so that it would also fit onto the threaded holes in the A250 T-slots, which are apparently a little bit...

Movable (T-Rail) holder for instruments and calibration cards. As is always the case, calibration cards are not easy to find exactly at the rare right moment)) Now, they are always on hand with the tool. Printed from wonderful...

ONLY for the SnapMaker 2.0 A350 Enclosure. I do not know if it fits others. 3 piece assembly so that the SnapMaker 2.0 A350 control pad is easily visible from the side. My 3D printer table setup has the longer side door panels facing me so the...

T-Nuts: Rotate it to print it upright. For M3 you need standard M3-Nut, DIN 934. For M4 you need flat M4-Nut, DIN 439. The Tube-Connector is a remix of https://www.thingiverse.com/thing:4175157 for 3mm Tubes. If using 4mm Tubes, use the Thing from...

This is a control panel enclosure for A350. ...It helps in few ways, protects screen, blocks light, and allows mounting of control panel else where. Takes just under 7 hours to print the door with a raft, sorry dont have timings for the main enclosure.

Really liked the sign, remixed adding a full plate with the letters built in for the model. ...

As I wanted to put my Snapmaker 2.0 A250 enclosure with its back to the wall, the clearance of the original filament holder (and the spool) was too much. When turning the filamentholder pointing to the front, the arm of the holder interferes with the...

You can find this item on Printables here: https://www.printables.com/model/153187-snapmaker-20-module-head-mount-for-enclosure This is a mount to hold 2x spare module heads and spare accessories that slots onto the side of the enclosure for an A250...

AboutI wanted to be able to conveniently place my Snapmaker's display on top of the enclosure and turned to the side, however wanted to keep it easy to move back to the enclosure and up again. ...So I've created this magnetic mount design that can slide...

easy and useful multiple spool holder for snapmaker 2.0 A350T, you need a 10mm steel rod

This is a mount to hold 2x spare module heads and spare accessories that slots onto the side of the enclosure for an A250 or A350 Snapmaker. The one photographed features an extra pocket on the side for other accessories but I've uploaded another...

A filament guard made to prevent filament to go on the left side of Z axis linear rail when printer is in A350 enclosure. Resolution doesn't matter, prints well from 0.24 to 0.32mm. ... Infill 20-30% No supports needed

Power supply holder for Snapmaker 2.0 Enclosure (tested on A350 but should work on A150 or A250 too - feedback is appreciated)

Here is a stand/mount for the Wyze Cam Pan for the Snapmaker 2.0 A350 with Enclosure. Designed it myself and it turned out pretty good for my use. I have it mounted on the bottom left extrusion with T nuts (still have to find some t nuts that fit...

In the A250 with Enclosure, the original Y axis adapter makes the cable chain hit the back of the enclosure, no matter the length of the chain. ...This part shortens 10mm the original part and with 14 links + ends you can cover the whole Y axis movement...

This part is a remix of a A350 part to make it if in a A250 where a) The rear part is split in two with a lock mechanism and can be printed in A250 b) Holes are displaced as the original part obstructs the case cable hole in an A250

In the A250 with Enclosure, the original Y axis adapter makes the cable chain hit the back of the enclosure, no matter the length of the chain. This part shortens 10mm the original part and with 14 links + ends you can cover the whole Y axis movement...

This works with the holey filament holder in this link: https://www.thingiverse.com/thing:4848261 I used a bit of glue and had it sit as far out as possible and angled to allow the easiest path for the filament to enter, then used this pipe kit :...

because you have the enclosure), use the Snapmaker swivel mount on the baseplate in the spot where the touchscreen holder would normally be mounted. This will require two M4x10 bolts and two M4 nuts. You also need to embed a third M4 nut on the...

Ich möchte ausdrücklich erwähnen das dies auf keinen Fall eine Absaugung ins Freie ersetzten kann(besonders beim Einsatz des Laser), ich kann weder beurteilen oder messen ob diese Art von Filter Wirkungsvoll arbeitet im Snapmaker/andere Maschinen! ...

You can find this item on Printables here: https://www.printables.com/model/153184-snapmake-20-a250-bed-and-tool-box-holder-for-enclo This is a holder which holds all the bed surfaces for the Snapmaker 2.0 A250T, as well as the tool box which comes...

This is a holder which holds all the bed surfaces for the Snapmaker 2.0 A250T, as well as the tool box which comes with the Snapmaker 2.0 and it slots onto the side of the enclosure. The print bed and CNC bed just slot onto the 'hook' holder on the...

I modified this to fit the 10w laser on one side. ... Remixed from https://www.thingiverse.com/thing:5265453

A windows Outlet for the Snapmaker Enclosure Exhaust tube

Remix of a couple of tool caddies. ...Designed to hang in the groove of a snapmaker artisan enclosure.

The SnapMaker enclosure profiles come equipped with simple snap-in clips that keep cables neatly organized. ...These clips effectively manage wires from lights and cameras, keeping them safely tucked away out of sight.

Simple filament guide I designed to mount to the Snapmaker enclosure top rail. ...Will also work on the linear axis depending on your setupI paired this with Filament arm mount for Snapmaker 2.0 enclosure (A350/F350) by Geddy | Download free STL model |...

Top Spool holder for the Snapmaker 2 Enclosure Parts: https://www.thingiverse.com/thing:3338467 1x Spring 1x Clutch 1x Dial 2x Clips 1x Hub https://www.thingiverse.com/thing:5438909 2x tnut