snapmaker enclosure 3d models

This is a handle that you can mount on one of the hinges on the enclosure door to make it easier to open and close the door fully. It is design to have the same look as the existing handle found on the enclosure. ... Includes handle for both doors...

I wanted to store my Palette Pro 2s on top of my Snapmaker enclosure and utilize a proper PTFE guiding system. I could not find anything that fit my setup so is designed this to match my setup. On my rail I have another one, in case I am storing a...

This is an enclosure designed for Snapmaker 2.0, I have an A250, so the size is suitable for A250. The main structure is based on the Aluminum profile(4040&2020), I will release the blueprint later after I improve it. It has 2 doors, and you can...

Update 20210307_______ASSEMBLY MANUAL ______________________________________________________________________ This is an enclosure designed for Snapmaker 2.0, I have an A250, so the size is suitable for A250. The main structure is based on the...

... textures with the main body. installation: Use the longer flat head M4 screws remaining in the enclosure frame installation Use two M3x8~12 or M4x8~12 screws for hanging rubber bands Black rubber band come in the package or any rubber band

... body. installation: Use the longer flat head M4 screws remaining in the enclosure frame installation Use two M3x8~12 or M4x8~12 screws for hanging rubber bands Black rubber band come in the package or any rubber band Category: 3D Printer Accessories

Replica of cable tie used in snapmaker 2.0 enclosure

The Snapmaker 2.0 Enclosure Corner Cover is the perfect finishing touch to complete the sleek design of the enclosure.

T-Nut for Snapmaker 2.0 Enclosure L: 30 mm Hole to hole : 20 mm v1 hexagon r: 3 mm v2 hexagon r: 2.9 mm

This bushing clips into the Snapmaker 2.0 Enclosure's filament passthrough bushing and holds a short section of 4mm OD PTFE tubing to reduce friction from the filament sharply changing direction.

For testing if it can slide into your Snapmaker 2.0 enclosure frame. ... It might be difficult to slide in for the 1st time, just don't give up too early.

This is an elbow for the enclosure on the Snapmaker 2.0. ...I would imagine most of you have your printers on a desk like mine and attaching a flexible duct for the exhaust fan was a bit tight.

Use this to support a piece of plywood above your Snapmaker 2.0 enclosure to prevent bowing/scratching on the glass. I'm using the short version to save on vertical space. I used 6 pieces total. ...Remixed from: https://www.thingiverse.com/thing:4643756...

Use this to support a piece of plywood above your Snapmaker 2.0 enclosure to prevent bowing/scratching on the glass. I'm using the short version to save on vertical space. I used 6 pieces total. ...Remixed from: https://www.thingiverse.com/thing:4643756...

I run a filament drying box inside the Snapmaker 2.0 Enclosure and rote the filament up and over the filament spool holder that comes with the Snapmaker 2.0. In preparation for the dual-filament print head and being able to string two different...

Use this to support a piece of plywood above your Snapmaker 2.0 enclosure to prevent bowing/scratching on the glass. I'm using the short version to save on vertical space. I used 6 pieces total. ... Remixed from:...

If you have the Snapmaker A250/A350 and the matching enclosure... well .. then you know that the filament is catching on the left column as the extruder is moving from the home position down. This nifty little mod makes sure the filament is guided...

This is a mount to hold an ESP32-CAM camera to the enclosure of a Snapmaker 2.0 enclosure. The components can be assembled to point the camera straight forward, 45º, or 90º from the enclosure wall. The clip can be mounted on any rail. Use the 5mm...

This is a little pull knob to make it easier to open the Snapmaker 2.0 enclosure doors. These install onto the existing holes on the doors. Replace the original M4x5 screw with an M4x10. It was designed for the A250 enclosure, but should work the...

This is a little pull knob to make it easier to open the Snapmaker 2.0 enclosure doors. These install onto the existing holes on the doors. Replace the original M4x5 screw with an M4x10. It was designed for the A250 enclosure, but should work the...

This is a little pull knob to make it easier to open the Snapmaker 2.0 enclosure doors. These install onto the existing holes on the doors. Replace the original M4x5 screw with an M4x10. It was designed for the A250 enclosure, but should work the...

I have moved a different printer into my Snapmaker 2.0 A150 enclosure (Prusa Mini+), so the gap in the door for the snapmaker controller is empty, so I made this. Simply print one of the covers, and a bunch of 'Cover clips'. It is easiest to...

A simple cap for the display hole in the Snapmaker 2.0 Enclosure. I've fixed my display in another location outside the enclosure (last picture) and this left a hole where it was by design which isn't best when using the laser head or printing...

I received my Snapmaker 2.0 A350 enclosure a week ago after having my printer for 8 months. Since getting the printer I've been using Octopi to control and monitor the printer. I couldn't figure out a good place to locate the octopi so I fired up...

After seeing the price of the filter made by Snapmaker I decided to make my own. This filter will connect to the hose provided by the enclosure for the v2.0 350 model. I used 2 HEPA filters which I sourced from Amazon. I wanted to make sure there...

Alle 3 Werkzeugköpfe inklusive dem passenden Snapmaker- Werkzeug Griffbereit am Gehäuse. Die Innenseiten sollten mit max 0.5mm starkem Filz beklebt werden, dann rappelt auch nichts. ... Mein allererstes Projekt, ich hoffe ihr könnt das brauchen.

Bien que ça ne soit pas une copie je me suis inspiré du très beau travail de (Snapmaker Filament mount by MrFen August 19, 2020) https://www.thingiverse.com/thing:4573894 Merci à lui pour cette bonne idée. ... Le support peut-être fixé en imprimant le...

Attach your touchscreen to the enclosure rail using four M4 screws and two T-Nuts. Slice with something other than Luban for quality. ... FreeCAD files added for modifications.

Attach your power supply to the enclosure using M4 screws. Slice with something other than Luban for quality. ... FreeCAD files added for modifications.

With the size of my A350 printer and enclosure and limited space, it is butted up in the corner and I cant use the standard holder that comes with the machine and be able to get spools on and off so i designed a bigger holder and reversed the...