snapmaker a250 dimensions 3d models

This is an upgraded version of chinkel's LM8LUU bearing blocks, designed with exact dimensions for precise fitment. I've recreated the model to accommodate offset requirements, making it an essential component for users seeking accurate printing...

The Snapmaker J1/J1s is a great printer, but one of my biggest complaints is that the bed is very slow to heat up and cool down. The glass bed does an excellent job of maintaining adhesion when heated and releasing when it's cooled down, but I...

The original spool holders on the snapmaker J1 are a little bit too short to handle spools with a little bit more substance. This spool holder fixes that. It is a direct replacement of the original spool holders. Print the spool holder and replace...

This lets you attach the GoPro to the Snapmaker 2 enclosure, either above or below the door sensor, on the same aluminum extrusion that holds it using holes and screws that come with the enclosure. To mount, one end goes into the corner...

This is a mounting arm for the Z-axis of a Snapmaker 2.0. Two lengths. Each length allows mounting a webcam; I think the longer arm gets a better angle on the print. The Z-axis arm can be used to mount anything else - feel free to make new...

Here is a recreation of the Anycubic Kossel Plus original carriage using its original dimensions. I created this design because some people might appreciate having spacers available for their 3D printers. The carriage features 42mm wide rod...

For all of you Lego Dimensions players who prefer not to have a stack of minifigs/vehicles hanging around but still want access to all of your characters in a slightly more ergonomic form factor.Here is a design which is easier to handle than the...

Made a movie as well and another one: see also www.rooiejoris.nl facebook.com/europerminutedesign http://www.thingiverse.com/joris Part one on printing in three dimensions, finally... can be found on: http://www.thingiverse.com/thing:75735 HISTORY...

Keep in mind that printer tolerance varies based on nozzle dimensions and material type. Therefore, it's essential to repeat the test for PETG, ABS, and other materials. ...If you switch between brands with the same material, the results tend to be...

I have watched many videos about finding the right 3d printer material temperature (there are many temperature towers), and many videos for understanding the tollerances of your printer. In both cases I haven't been satisfied at all. with the...

I have only created 180-degree left and right storage bins with 1, 2 and 3 drawers for the Snapmaker 1kg Spools, sizes 198x81x55 and 198x89x57. For spool size 198x89x57, use 'StorageBinsClips_Flat_Head' clips to secure the bin, no need for...

This is a complete overhaul of my original Snapmaker GoPro Mounts (https://www.thingiverse.com/thing:2799487). I've added many more mounts, including bed mounts that will move along with the bed movements without interfering with leveling or reducing...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 50 use_mouse_ears = 0 custom_back_camera_x_size = 23...

The extruders are mounted using the same procedure.Made with Onshape:Source CAD: Snapmaker Artisan Modular Side ShelvingPrint Recommendations:Print in PETG for the increased strength.Rotate the models so they are laying down, bosses facing up.Print...

Rewind spool holder for Snapmaker 2 A250 / A350. Designed to accommodate spools of inner diameter 45-90mm perfectly. A stiff spring provides sufficient tension for approximately 1.5-2 turns, ensuring a reliable rewind experience. To further enhance...

It was designed for the A250 enclosure, but should work the same with the A150 and A350 enclosures. I'm sure the model could be improved with some rounded edges, but sanding got me where I'm trying to go. ...This thing is easy to print, easy to...

It was designed for the A250 enclosure, but should work the same with the A150 and A350 enclosures.I'm sure the model could be improved with some rounded edges, but sanding got me where I'm trying to go. ...This thing is easy to print, easy to install,...

It was designed for the A250 enclosure, but should work the same with the A150 and A350 enclosures.I'm sure the model could be improved with some rounded edges, but sanding got me where I'm trying to go. ...This thing is easy to print, easy to install,...

Some connectors from http://www.tunik.com.trTMK2000 series connectorsApprox dimensions, approximate dimensions, just for reference in PCB design

Some connectors from http://www.tunik.com.trTMK2000 series connectorsApprox dimensions, approximate dimensions, just for reference in PCB design

Power supply holder for Snapmaker 2.0 Enclosure (tested on A350 but should work on A150 or A250 too - feedback is appreciated)

Simple little pull-tab 'handle' to make it easier to "buckle" the Snapmaker 2.0 A250 Enclosure sliding door at the outward part of the tri-fold, while opening. Printed in PLA with 2 layers or so (0.24mm layers) top, bottom, and sides, and 15% or...

A simple cap for the display hole in the Snapmaker 2.0 Enclosure. I've fixed my display in another location outside the enclosure (last picture) and this left a hole where it was by design which isn't best when using the laser head or printing...

Element clamp for yagi antenna .08, 10, 12mm Eléments clamp for 15 AND 20mm boom.The same support for 3 dimensions of yagi antenna elements and for 2 dimensions of square boom.Also 08, 10, 12 mm elements clamp for 15 or 16 / 20 / 25 and 30mm...

CNC dust shoe for snapmaker original.

Card Holder for Snapmaker 2.0 Laserbed. ...

CNC Fixture Plate For Snapmaker Artisan

Displayholder for the Snapmaker 2.0

Snapmaker Artisan CNC Platform T-groove

Remix of Snapmaker Laserbed clip by Darthwolff.