snapmaker 2 3d models

This is a frame to fit the snapmaker 2.0 enclosure hole for the display. the hole for the display in the door is much bigger that the actual display, så laser lights is visible and could harm kids, animals, etc. this frame fits in the hole and...

Noise dampening pad for Snapmaker 2.0 (probably 1.0 as well) laser bed. The stock bed is only fixed in the centre and rattles as it moves. I printed some of these out of TPU and put them on the attachment points (all of them, not just the ones with...

**Update to new version: Added cutout for auto-thickness laser, further recessed lasers to allow for manual thickness while cross is still attached** This is a laser cross I designed for the Snapmaker 2.0 10W laser. I got tired of trying to find the...

Spool holder for Snapmaker 2.0 Material required: - 1x M4x15mm - 2x Ball bearing (inside Ø8mm / outside Ø22mm / width 7mm) Assembly: - Remove the filament holder rod - Put a ball bearing on one side of the rod (mine was nor perfectly round so i had...

phone holder for snapmake 2.0

So I found a Youtube video that tells you how to reduce the noise from the snapmaker 2.0 power supply fan. Basically, the hack is to just to unplug the noisy 40mm fan at the back. The only issue is that cooling for the power supply is reduced. It...

So I found a Youtube video that tells you how to reduce the noise from the snapmaker 2.0 power supply fan. Basically, the hack is to just to unplug the noisy 40mm fan at the back. The only issue is that cooling for the power supply is reduced. I've...

Winkel für die Z Achse des Snapmaker 2.0 und A350 in originaler Form und eine in "stabilisiert" , um noch bessere Winkelstabilität zu erhalten , da "nur" 3-D druckWinkel original und stabilisiert mit Zusatzlöcher für mein Quick-Swap-Kit-Update...

I remixed for Snapmaker 2.0(A250). Small inner diameter provide smooth spool rotation. You can edit Fusion360 (.f3d) file sketch for own printer spool shaft diameter,length,etc... ...

I remixed for Snapmaker 2.0(A250). Small inner diameter provide smooth spool rotation. You can edit Fusion360 (.f3d) file sketch for own printer spool shaft diameter,length,etc... Category: 3D Printer Accessories

#### Description **This model was designed for the official Snapmaker Original Enclosure and NOT designed for any Snapmaker 2.0 models or accessories.** This is an experimental spool holder of [TUSH - The Ultimate Spool...

Deutsch Schutzkappe für den original 10W Laser von Snapmaker 2.0. Ich habe hier nur Kappen für den kleinen Laser gefunden, darum hier das neue Design. Das Design hat eine Presspassung und rutscht nicht von selbst ab, daher empfehle ich den Druck...

These Brackets secure the CREALITY CR-200B 240mm x 220mm x 4mm Glass plate to the Snapmaker 2.0 A250 bed. You need to print two brackets I recommended use M4x14 screws PLEASE NOTE: Auto level doesn't work with this glass. You must turn...

Name: Tiny Snapmaker Designer: Howard Info: This compact Snapmaker 3D printer packs a big punch. ... More Details are available in the snapmaker community forum at http://forum.snapmaker.com.

# Laser Exhaust Attachment for 10W Snapmaker Laser ##[Mini Dust Collection](https://www.thingiverse.com/thing:5805774) ##[Exhaust Extension](https://www.thingiverse.com/thing:5847318) ##[Snapmaker Vacuum...

This is a stepped file for testing laser etching on the SnapMaker 2.0 10w Laser Module. It was created in Luban and varies laser power in 10% increments on the x-axis, and speed in 100mm/min increments on the y-axis. ... The sample image was done on...

Parts list & hardware: Here's what is included and the minimal hardware that's needed: BASE option A — M3x16 screws x 2 (This can be attached to Snapmaker 2.0 enclosure vertical beam near touchscreen.) Then to attach the next flex arm segment...

Simple little pull-tab 'handle' to make it easier to "buckle" the Snapmaker 2.0 A250 Enclosure sliding door at the outward part of the tri-fold, while opening. Printed in PLA with 2 layers or so (0.24mm layers) top, bottom, and sides, and 15% or so...

These Brackets secure the CREALITY 310mm x 310mm x 4mm Glass to the Snapmaker 2.0 A350 bed. As we all know the A350 bed is very bad for flatness, mostly around the outer 50-75mm. This helps, but my end goal is to shim the heat plate to flat and...

Prevent the Heated Bed Cable from catching on the end of the linear module on the Snapmaker 2.0. This design is to compensate for the small space available when the printed bed is all the way back in the A350 Enclosure. Tip: Snap the chain link...

Prevent the Heated Bed Cable from catching on the end of the linear module on the Snapmaker 2.0. This design is to compensate for the small space available when the printed bed is all the way back in the A350 Enclosure. Tip: Snap the chain link...

I REMADE THIS FOR SNAPMAKER

With today being the release of the Snapmaker 2, I thought it was time to share this with the community. If you're not printing on the original Snapmaker, you can do both sides in one go using the Left/Right stl's (no top/bottom in name). However,...

... has also been truncated for easy pass-through. This QC bracket set was designed for Snapmaker 2.0 machines and was not compatibility tested for other versions or models of Snapmaker. ** Watch for future accessories of the FLEXI range! ...**

Name: Flowerpot Designed by: Leonardo Details: Discover more about this project at the Snapmaker community forum: http://forum.snapmaker.com/

... This particular design is tailored for cutting out dice from 1.5mm thick wood using a Snapmaker 1600mW Laser cutting module. Prepare: 1. I'll need access to the Snapmaker 1600mW Laser cutting module. 2. The material required is 1.5mm thick wood.

Used with an A350, it will likely work with smaller versions of the SnapMaker 2 as well. This modification solves the issue of filament coming off the reel when the machine moves to home position. Default setup is for a small spool with a 32mm...

However, filament and printer variations may require slight adjustments: printing it 1-2% larger or applying electrical tape to the pegs can achieve a tighter grip. ... For a more secure hold on flat cables, users can apply tape or heat shrink tubing -...

... on handcrafted items. ...Here's a unique project that showcases the fusion of laser and 3D printing technology. To learn more about Snapmaker's community and innovative ideas, visit http://forum.snapmaker.com The "Vintage Skull" was crafted by @asil

... box impressively stores all the Snapmaker accessories in a stylish and minimalist design. More Information on snapmaker community : http://forum.snapmaker.com/t/snapmaker-showcase-snapbox/336 Print Tips: https://www.instructables.com/id/32Snapbox/