snapmaker 2 a350 3d models

A simple shroud to cover the Y connectors on the base of the Snapmaker A350. Hides wires, protects from dust, and has a sloped front edge to keep the heated bed cable from getting in a bind. ...Recommended print orientation is with open side facing up ...

The air duct attaches to the laser bed of the Snapmaker A350 to provide air assist and smoke extraction. The duct is designed to fit a 100mm flexible air duct that can be connected to an extraction fan. ... The has slots and holes on the sides to fit...

Prevent the Heated Bed Cable from catching on the end of the linear module on the Snapmaker 2.0. This design is to compensate for the small space available when the printed bed is all the way back in the A350 Enclosure. Tip: Snap the chain link...

Prevent the Heated Bed Cable from catching on the end of the linear module on the Snapmaker 2.0. This design is to compensate for the small space available when the printed bed is all the way back in the A350 Enclosure. Tip: Snap the chain link...

Yi home camera mount for A350

--------------------------------------------------------------------------------------------------------------------------------------------------------------- Snapmaker2.0 Touch Panel Controller Holder Compatible model: Snapmaker2.0 A250/A350...

--------------------------------------------------------------------------------------------------------------------------------------------------------------- Snapmaker2.0 Touch Panel Controller Holder Compatible model: Snapmaker2.0 A250/A350...

Plates PVC foam plate 13 mmHard ware FATHSome parts you can print with your snapmaker

Master Repository: https://github.com/spitzlbergerj/Snapmaker-Dimensions I will put here my technical drawings of modules of Snapmaker 2.0 A350. These serve me as a basis for the development of accessories for the Snapmaker 2.0 The drawings are made...

I will put here my technical drawings of modules of Snapmaker 2.0 A350. These serve me as a basis for the development of accessories for the Snapmaker 2.0 The drawings are made by simply measuring the dimensions. So tolerances are possible within the...

... using double sided tape. Being a .jpg image, it can easily be edited to suit controllers with different port configurations. This was designed for the Snapmaker 2.0 A350 and was not compatibility tested for other versions or models of Snapmaker.

This is an adapter for a vinyl cutter / blade holder for the Snapmaker 2.0 A350. The adapter is designed for a blade holder compatible with Graphtec CB09 CB09U: ...

This is an adapter for a vinyl cutter / blade holder for the Snapmaker 2.0 A350. The adapter is designed for a blade holder compatible with Graphtec CB09 CB09U: ...

... easy setup for A250 and A350 Snapmaker printers rotary accessory. ... Stationary arm 100mm Stationary arm 130mm Mounting rail for A250 & A350 Adjustable rolling arm mount Adjustable rolling arm "Hardware 4 M4 screws 4 608 bearings 2.2 x 0.8 x 0.7 cm"

Parts list & hardware: Here's what is included and the minimal hardware that's needed: BASE option A — M3x16 screws x 2 (This can be attached to Snapmaker 2.0 enclosure vertical beam near touchscreen.) Then to attach the next flex arm segment...

I was forever frustrated with the basic Snapmaker 2.0 A350 filament mount. The unit stretched so much filament from the spool as it prepared to print that the excess filament would fall off the spool and risk being tangled. I ended up babysitting my...

I was forever frustrated with the basic Snapmaker 2.0 A350 filament mount. The unit stretched so much filament from the spool as it prepared to print that the excess filament would fall off the spool and risk being tangled. I ended up babysitting my...

Work in progress... ... chain: https://www.amazon.com/gp/product/B098NV15C3

Camera mount for the AliExpress USB camera https://www.aliexpress.com/item/1005001639797152.html

Camera mount for the AliExpress camera https://www.aliexpress.com/item/1005001639797152.html You must make M4 thread in camera_mount_1. ...Part 3 can be mounted on the enclosure rails with M4 6mm 2020 nuts.

A simple Press-Fit Case for a RaspberryPi3B+ (And all Raspberrys with the same size) With a Mounting-Point for the Z-Axis of the Snapmaker 2.0 A350 (Can fit other Snapmaker Models too) No Venting-Holes (To keep Dirt out of the case when operating the...

Snapmaker 2.0 A350 cable bed 45 degree angle Snapmaker seems to have a problem with the cable from the heated bed, that breaks because bending the way is. so I have a re design with a 45 degree angle so it bends on the flat side not the short side. ...

https://www.amazon.com/gp/product/B01LH1G2IE/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1 Tnisesm Miniature Power Relay DC 24V Coil, 30A SPDT (1NO 1NC) 120VAC NT90-DC24V You MUST use a 24v relay, the Snapmaker A350 Exhaust fan is a 24v fan. I...

Created to add less stress on the gears of my snapmaker 2 a350. ...Fits Hatchbox spool.

The new Snapmaker 10W laser is bigger (thicker) than the original 1.6W by 6 mm. This difference offset the center of the new laser from the original (and wonderful!) Y-Axis roller. I couldn't find any screw locations that worked so I remixed the...

Hey, so we all know that the Snapmaker printplate is trash and is mostly impossible to become leveled correctly, so I bought Anycubic Ultrabase 330x310 glassplate and now it works like a charm. The clamps are so disigned that the fan wont hit the...

I (unfortunately) made my custom enclosure to the same size as the Snapmaker enclosure, which means there's no "good place" to mount the camera to the bed so your item doesn't move in frame, if you mount it at the front of the bed, when you move the...

Use screws M4x10 and M4x12 =================================================================== Bac de Rangement à fixer aux extrémités des 2 modules linéaires Y. Compatible avec ou sans enclosure. Conçu pour être installé à l'avant ou à l’arrière...

Ersatzteil zum Ausdrucken für den Snapmaker 2 Druckkopf

... Snapmaker A350 Bed Holder - Elevate Your CNC and Laser Experience. ... The Snapmaker A350 Bed Holder is specifically designed to work seamlessly with both your CNC table and laser table, ensuring maximum efficiency and precision in all your projects.